Elixir M2Y2G64CB8HC5N-CG User Manual
M2Y2G64CB8HC5N / M2Y2G64CB8HC9N
2GB: 256M x 64
Unbuffered DDR3 SDRAM DIMM
REV 1.1
4
01/2010
© NANYA TECHNOLOGY CORP.
NANYA TECHNOLOGY CORP. reserves the right to change Products and Specifications without notice.
Input/Output Functional Description
Symbol
Type
Polarity
Function
CK0, CK1
,
Input
Cross
point
The system clock inputs. All address and command lines are sampled on the cross point of the
rising edge of CK and falling edge of
rising edge of CK and falling edge of
. A Delay Locked Loop (DLL) circuit is driven from the
clock inputs and output timing for read operations is synchronized to the input clock.
CKE0, CKE1
Input
Active
High
Activates the DDR3 SDRAM CK signal when high and deactivates the CK signal when low. By
deactivating the clocks, CKE low initiates the Power Down mode or the Self Refresh mode.
deactivating the clocks, CKE low initiates the Power Down mode or the Self Refresh mode.
,
Input
Active
Low
Enables the associated DDR3 SDRAM command decoder when low and disables the
command decoder when high. When the command decoder is disabled, new commands are
ignored but previous operations continue, Rank 0 is selected by
command decoder when high. When the command decoder is disabled, new commands are
ignored but previous operations continue, Rank 0 is selected by
; Rank 1 is selected by
,
,
Input
Active
Low
When sampled at the positive rising edge of CK and falling edge of
, signals
,
,
define the operation to be executed by the SDRAM.
ODT0, ODT1
Input
Active
High
Asserts on-die termination for DQ, DM, DQS, and
signals if enabled via the DDR3 SDRAM
mode register.
DM0
– DM8
Input
Active
High
The data write masks, associated with one data byte. In Write mode, DM operates as a byte
mask by allowing input data to be written if it is low but blocks the write operation if it is high. In
Read mode, DM lines have no effect.
mask by allowing input data to be written if it is low but blocks the write operation if it is high. In
Read mode, DM lines have no effect.
DQS0
– DQS8
–
I/O
Cross
point
The data strobes, associated with one data byte, sourced with data transfers. In Write mode,
the data strobe is sourced by the controller and is centered in the data window. In Read mode,
the data strobe is sourced by the DDR3 SDRAM and is sent at the leading edge of the data
window.
the data strobe is sourced by the controller and is centered in the data window. In Read mode,
the data strobe is sourced by the DDR3 SDRAM and is sent at the leading edge of the data
window.
signals are complements, and timing is relative to the cross point of respective
DQS and
. If the module is to be operated in single ended strobe mode, all signals
must be tied on the system board to V
SS
and DDR3 SDRAM mode registers programmed
appropriately.
BA0, BA1, BA2
Input
-
Selects which DDR3 SDRAM internal bank of four or eight is activated.
A0
– A9
A10/AP
A11
A12/
A13
Input
-
During a Bank Activate command cycle, defines the row address when sampled at the cross
point of the rising edge of CK and falling edge of
point of the rising edge of CK and falling edge of
. During a Read or Write command cycle,
defines the column address when sampled at the cross point of the rising edge of CK and
falling edge of
falling edge of
. In addition to the column address, AP is used to invoke autoprecharge
operation at the end of the burst read or write cycle. If AP is high, autoprecharge is selected
and BA0-BAn defines the bank to be precharged. If AP is low, autoprecharge is disabled.
During a Precharge command cycle, AP is used in conjunction with BA0-BAn to control which
bank(s) to precharge. If AP is high, all banks will be precharged regardless of the state of
BA0-BAn inputs. If AP is low, then BA0-BAn are used to define which bank to precharge.
and BA0-BAn defines the bank to be precharged. If AP is low, autoprecharge is disabled.
During a Precharge command cycle, AP is used in conjunction with BA0-BAn to control which
bank(s) to precharge. If AP is high, all banks will be precharged regardless of the state of
BA0-BAn inputs. If AP is low, then BA0-BAn are used to define which bank to precharge.
DQ0
– DQ63
Input
-
Data Input/Output pins.
V
DD
,
V
DDSPD,
V
SS
Supply
-
Power supplies for core, I/O, Serial Presence Detect, Temp sensor, and ground for the module.
V
REFDQ,
V
REFCA
Supply
-
Reference voltage for SSTL15 inputs
SDA
I/O
-
This is a bidirectional pin used to transfer data into or out of the SPD EEPROM and temp
sensor. A resistor must be connected from the SDA bus line to V
sensor. A resistor must be connected from the SDA bus line to V
DDSPD
on the system planar to
act as a pull up.
SCL
Input
-
This signal is used to clock data into and out of the SPD EEPROM and Temp sensor.
SA0
– SA2
Input
-
Address pins used to select the Serial Presence Detect and Temp sensor base address.
Output
-
The
pin is reserved for use to flag critical module temperature.
Input
-
This signal resets the DDR3 SDRAM