Controlled Entry Distributors Inc. FFIII318LI1 User Manual

Black Case with Blue Buttons

Push

Buttons

Made in Taiwan.  Copywrite © 2015 Community Controls.

The warranty period of Community Controls Firefly3™ transmitters is 

twenty-four (24) months.  This warranty shall begin on the date the 

transmitter is manufactured.  During the warranty period, the product will be 

repaired or replaced (at the sole discretion of Community Controls) if the 

product does not operate correctly due to a defective component.  This 

warranty does not extend to (a) the transmitter case, which can be damaged 

by conditions outside the control of Community Controls, or (b) battery life 

of the transmitter.  This warranty is further limited by the following disclaimer 

of warranty and liability:

EXCEPT AS SET FORTH ABOVE, COMMUNITY CONTROLS MAKES NO WARRANTIES REGARDING THE 
GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS 
FOR A PARTICULAR PURPOSE.  BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF COMMUNITY 
CONTROLS, EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”. 
COMMUNITY CONTROLS SELLS THE GOODS TO BUYER ON CONDITION THAT COMMUNITY CONTROLS 
WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE.  BUYER AGREES THAT COMMUNITY 
CONTROLS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO BUYER, ITS 
EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE.  BUYER ALSO AGREES TO HOLD COMMUNITY 
CONTROLS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF 
BUYER’S USE OR DISPOSAL OF THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS 
TERMS IN CONSIDERATION OF RECEIVING THE GOODS.

Any changes or modifications to Community Controls equipment not 

expressly approved by Community Controls could void the manufacturer’s 

warranty and could void the user’s authority to operate the equipment.

3

Linear’s MegaCode® series of digital transmitters are wireless radio controls 
designed for use with MegaCode format receivers. The MegaCode radio 
format provides unparalleled security. Each transmitter is pre-set at the factory 
to one of over 1,000,000 codes. The 318FixedCode is a two-button 
transmitter that sends a unique code to a single device. The transmitter is 
powered by one Type "23A 12V" batteries.

Operating frequency :   

318MHz

Number of buttons :    

2

Battery :             

1 ea. 12V A23

Operating temperature :   -20°F - 85°F
Overall dimensions :    

2-1/8 x 1-9/16 x 1/2 inch

Weight: 

 

1 oz.

To access the battery, remove the set screw. Next, place a flat object such as

a coin in the top corner notch of the case.  Twist the object gently to open the 

case. Attend to proper polarity when installing or replacing the battery.  When

complete, squeeze the top and back cover gently together until the case is 

completely closed, then replace and tighten the screw.
NOTE: Please  dispose of  the  batteries  properly  according to  local  laws 

Each transmitter is manufactured and  sold with a  different factory- set  serial number.

The transmitter must be programmed into your system memory. 

Your own installer or reseller will provide you the necessary instructions for your 

system.

A -  Firmly depress the button until the small red LED illuminates.

B -  After the LED has illuminated, release the button. 

If the device you are attempting to activate does not respond, repeat steps A and 

B or consult section 7 ( Troubleshooting ) of this manual.

The system does not receive the transmitter signal
The transmitter led is OFF
The transmitter led is blinking
The operating range is reduced

The system does not receive the transmitter signal
The transmitter led is ON .

 

Replace the transmitter 

battery

Check the power supply 

of the receiver

Screw

Case

Notch