Weifang Goertek Electronics Co. Ltd GBDA90 User Manual

Page of 2
GBDA90
The GBDA90 adapter allows you to use an Apple iPod
®
 
with your Bluetooth stereo headset. The adapter utilizes 
Bluetooth technology to stream stereo music wirelessly. 
GBDA90 supports your controlling iPod
®
 with the buttons 
on your Bluetooth stereo headset. 
Please note: GBDA90 requires an iPod
®
 with a dock 
connector. This includes the third generation iPod
®
, the 
forth generation Click Wheel iPod
®
, iPod
®
 Photo, iPod
®
 
mini, iPod
®
 nano, and the fifth generation iPod
®
 with 
Video. GBDA90 works with any of these, and there is no 
additional software to install on the iPod
®
.
GBDA90
TROUBLESHOOTING
Cannot pair with the Bluetooth stereo head-
set
When attempting to pair, make sure no other nearby 
Bluetooth devices are in paring mode or discoverable 
mode, and ensure that all previously paired Bluetooth 
devices are powered off.
SUPPORT
If you need further help, please contact us:
GoerTek Technology Co.,Ltd.
http: //www. goertek. com
e-mail: service@goertek. com
Customer Service Hotline: 86-532-88999318
The copyright and brand name are owned by the register. All information in 
this manual is subject to change without prior notice.
GoerTek has the authority to explain the above information.
For more information, please visit GoerTek Website:
http: //www.goertek.com
GETTING STARTED
2. Connect GBDA90 to the dock connector at the bottom 
of your iPod
®
 (Please make sure the Power on/off button 
on GBDA90 is at On position). GBDA90 and iPod® will 
power on automatically.
If GBDA90 is already connected to your iPod
®
, simply 
power on and play your iPod
®
. (GBDA90 will not power 
on until the iPod
®
 has resumed playing.) 
After a few moments, the light on GBDA90 will blink 
green once every 4 seconds to indicate the wireless 
connection with the Bluetooth stereo headset.
You can now control your iPod
®
 wirelessly with the 
button on your Bluetooth stereo headset.(Please refer to 
the manual of your Bluetooth stereo headset for details).
Sleeping Mode
GBDA90 will go into Sleeping mode as iPod
®
 enters 
Sleep mode, during which indicator light is off. GBDA90 
will wake up immediately as soon as PLAY of iPod
®
 is 
pressed.
DO NOT MODIFY OR DISMANTLE
Do not attempt to open GBDA90. Doing so may expose 
you to electric shock and serious injury. There are no 
user-serviceable parts inside. Any attempt to alter or 
repair the module will void the limited Warranty. Users 
are not permitted to make changes or modify the device 
in any way. Changes and modifications void the user’s 
authority to operate the device. 
TROUBLESHOOTING
No audio is heard on the Bluetooth stereo 
headset
For GBDA90 to work properly, it must be correctly paired 
with the Bluetooth stereo headset. (See section titled 
Pairing, for instructions in performing this one-time task.) 
If pairing was successful and you still can’t hear music, 
try the following:
1. Make sure the iPod
®
 is playing and fully seated into 
GBDA90
2. Make sure Power on/off button on GBDA90 is at the 
On position
3. Check the volume level on both your iPod
®
 and the 
Bluetooth stereo headset.
iPod
®
 Nano 2G sleeve
GBDA90
Note: when you use GBDA90 with other iPod
®
 products 
except of nano 2G, you should take off the sleeve for 
mounting.
CHARGING
No charging is required because GBDA90 has not built-
in battery. It uses your iPod® for the small amount of 
power supply, so be sure your iPod
®
 is fully charged.
GETTING STARTED
Power on/off
When GBDA90 is connected to the dock connector at 
the bottom of your iPod
®
, you can power on or off 
GBDA90 by sliding Power on/off button to the On or Off 
position. 
You can also remove GBDA90 from iPod
®
 to power off it 
directly.
Note: GBDA90 can not be powered on without connect-
ing to iPod
®
 because it is powered by iPod
®
 built-in 
battery.
Pairing
Pairing is a one-time task that allows GBDA90 and the 
Bluetooth stereo headset to recognize each other for 
future use.
GETTING STARTED
To pair GBDA90 with the Bluetooth stereo 
headset
If you have other Bluetooth devices, be sure they are 
powered off before proceeding
1. Connect GBDA90 to the dock connector at the bottom 
of your iPod
®
 (Please make sure the Power on/off button 
on GBDA90 is at On position). The indicator light on 
GBDA90 will blink Red->Amber->Green, and then turn to 
solid Red. (Figure 1)
2. Please  turn your Bluetooth stereo headset to pairing 
status.(Please Refer to the user guide of your Bluetooth 
stereo headset for details). 
When pairing is successful, the indicator light on 
GBDA90 will flash green ten times rapidly and then blink 
green once every 4 seconds, ready for use. 
After GBDA90 and the Bluetooth stereo headset have 
been successfully paired, they will automatically connect 
when both are powered on and placed within 100 meters 
of each other. 
GETTING STARTED
Note:  You will need to remove the sleeve, press the 
front center of the sleeve lightly and pull it upwards away 
from the GBDA90 adapter.
Through Charging and Data Transferring 
You can charge your iPod
®
 through GBDA90 without 
disconnecting it from iPod
®
. Plug the power adapter or 
USB charging cable into USB charging port of GBDA90,  
and then you iPod
®
 can be charged by through GBDA90.  
Also you can transfer the data from your computer to 
iPod through GBDA90 without disconnecting it from iPod 
when you connect GBDA90 with the computer via the 
USB cable.
General Use
After the initial pairing, you can restore the wireless 
connection between the Bluetooth stereo headset and 
GBDA90 with just a few simple steps. Make sure your 
iPod
®
 and the Bluetooth stereo headset are properly 
charged then do the following:
1. Power on the Bluetooth stereo headset. (Refer to the 
user manual of your Bluetooth stereo headset for 
details).
Indicator Light
iPod
®
 30-pin Connector    
Disconnect button
Disconnect button
Power on/off switch
USB charging port
Figure 1