Long-E Technology Co. Ltd. TA31TA37 User Manual
GS-500A W/O ANTI HIJACKING FUNCTIONAL MANUAL Page 1 of 5
TA37
ANTI HIJACKING FUNCTIONAL MANUAL
Button Press
function
Conditions
0.5 seconds
Arm/door lock
Lock the door
Stop alarm sounding
Lock the door
Stop alarm sounding
Alarm is disarmed
In valet mode
Alarm sounding
In valet mode
Alarm sounding
1
2 seconds
panic
Anytime
0.5 seconds
Disarm/door unlock
Unlock doors
Stop alarm sounding and disarm
Unlock doors
Stop alarm sounding and disarm
Alarm is being armed
In valet mode
Alarm sounding
In valet mode
Alarm sounding
2
2 seconds
Auxilary 1 output (trunk release)
Anytime
1Æ1
Æ
Within 5 seconds
Arm bypassing shock sensor
Alarm is disarmed
1+2
+
2 seconds
Auxilary 2 output
Anytime
2Æ2
Æ
Within 5 seconds
Passenger unlock
Alarm is being armed
3
2 seconds
Car finder
Anytime
3Æ1
Æ
Within 10 seconds
Silent arming/door lock
Alarm is disarmed
3Æ2
Æ
Within 10 seconds
Silent disarming / door unlock
Alarm is being armed
4
0.5 seconds
Shift for 2 car operation
Anytime
The system is supplied with two 4-buttons remote transmitters used to control system operations.
Button 1 arms the system and when held for 2 seconds, activates the system’s panic feature. Button 1 also locks the doors when
the system is in valet mode.
Button 2 disarms the system. Pressing button 2 again operates the passenger unlock feature (if installed). Button 2 also unlocks
the doors when the system is in valet mode. To hold the button 2 for 2 seconds shall activate the auxiliary channel output 1 for
trunk release function; This output will remain on for as long as the button is pressed.
Button 3 activates the silent operation for the arming and disarming.
Press button 3 then button 1 arms the system silently.
Press button 3 then button 2 disarms the system silently.
Press button 3 for 2 seconds activates the vehicle locator feature which flashes the parking lights and chirps the siren 5 times.
This feature is useful to help locate the vehicle in a crowded parking lot.
Button 1+2 activates the auxiliary 2 output. This output will remain on for as long as the button is pressed.
Button 4 is the page shift button. The page shift button will change the function of buttons 1 through 4 each time it is pressed,
allowing access to additional features or multiple car operation. Each time the shift button is pressed, the led on the transmitter
will illuminate and the transmitter functions will shift to the next page, allowing access to another set of features. Once shifted to
another page(there are 4 pages total), the transmitter will remain on that page for 10 seconds or until a button is pressed, then
return to page 1. each time a transmitter button is pressed and held, the led will flash a number of times to indicate from which
page it is transmitting. Under normally operation, only pages 1 and 2 are used. Page 3 and 4 are usually used for two car
operation.
1. ADDING/REPLACING TRANSMITTERS (Code learning)
To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and
follow the steps below.
NOTE: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure
to program all 4 transmitter memory location.
To program the transmitter(s):
1) Turn on the ignition key on, off, on, off, and back on.
Button 1 arms the system and when held for 2 seconds, activates the system’s panic feature. Button 1 also locks the doors when
the system is in valet mode.
Button 2 disarms the system. Pressing button 2 again operates the passenger unlock feature (if installed). Button 2 also unlocks
the doors when the system is in valet mode. To hold the button 2 for 2 seconds shall activate the auxiliary channel output 1 for
trunk release function; This output will remain on for as long as the button is pressed.
Button 3 activates the silent operation for the arming and disarming.
Press button 3 then button 1 arms the system silently.
Press button 3 then button 2 disarms the system silently.
Press button 3 for 2 seconds activates the vehicle locator feature which flashes the parking lights and chirps the siren 5 times.
This feature is useful to help locate the vehicle in a crowded parking lot.
Button 1+2 activates the auxiliary 2 output. This output will remain on for as long as the button is pressed.
Button 4 is the page shift button. The page shift button will change the function of buttons 1 through 4 each time it is pressed,
allowing access to additional features or multiple car operation. Each time the shift button is pressed, the led on the transmitter
will illuminate and the transmitter functions will shift to the next page, allowing access to another set of features. Once shifted to
another page(there are 4 pages total), the transmitter will remain on that page for 10 seconds or until a button is pressed, then
return to page 1. each time a transmitter button is pressed and held, the led will flash a number of times to indicate from which
page it is transmitting. Under normally operation, only pages 1 and 2 are used. Page 3 and 4 are usually used for two car
operation.
1. ADDING/REPLACING TRANSMITTERS (Code learning)
To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and
follow the steps below.
NOTE: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure
to program all 4 transmitter memory location.
To program the transmitter(s):
1) Turn on the ignition key on, off, on, off, and back on.
The sire will chirp 3 times.
2) Press and hold the override switch for
3
seconds.
The siren will chirp 5 times. The led will illuminate.
3) Press any button on the first transmitter.
The siren will chirp once.
4) Press any button on the first transmitter again.
The siren will chirp twice to indicate it has learned the code.
5) Repeat steps 3 and 4 for each transmitter (up to 4).
6) Turn off the ignition key.
***TWO CAR OPERATION
If two vehicles are equipped with this system, for convenience both can be operated using the same remote transmitter. If all four
6) Turn off the ignition key.
***TWO CAR OPERATION
If two vehicles are equipped with this system, for convenience both can be operated using the same remote transmitter. If all four
transmitters are to be used with both cars, program transmitters A and B into the first vehicle in the manner described above.
Program transmitters C and D by pressing the shift button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second vehicle as normal, then program
transmitters A and B by pressing the shift button twice before performing steps 3 and 4 above.
When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing the shift button
twice and the desired function button.
Program transmitters C and D by pressing the shift button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second vehicle as normal, then program
transmitters A and B by pressing the shift button twice before performing steps 3 and 4 above.
When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing the shift button
twice and the desired function button.
2. REMOTE ARMING
The system monitors independent areas (zones) while armed: doors, hood/trunk, shock sensor and optional sensor input.
To arm the system:
1) Turn off the ignition.
2) Press button 1.
The system monitors independent areas (zones) while armed: doors, hood/trunk, shock sensor and optional sensor input.
To arm the system:
1) Turn off the ignition.
2) Press button 1.
The siren will chirp once. The doors will lock. The parking lights will flash once. The led will turn on red, to indicate the
starter defeat is activate.
3) 5 second after arming:
3) 5 second after arming:
The led will start blinking to indicate that the doors and hood/trunk inputs are being monitored. (see function selection #11 for
door input monitoring on the delay time)
z During arming, if the system detects a bad sensor or an open zone, the system will chirp 4 additional times and ignore that
z During arming, if the system detects a bad sensor or an open zone, the system will chirp 4 additional times and ignore that
input, but keep all other areas protected.
Once armed, the alarm will trigger when any of the following occurs:
The doors are opened. The hood or trunk is opened. The shock senor detects an impact to the vehicle. The optional sensor is
disturbed.
When the alarm triggers, the siren will sound, the horn will honk, and the parking lights will flash, the led will flash rapidly. The
system alarm will last for 30 seconds.
The doors are opened. The hood or trunk is opened. The shock senor detects an impact to the vehicle. The optional sensor is
disturbed.
When the alarm triggers, the siren will sound, the horn will honk, and the parking lights will flash, the led will flash rapidly. The
system alarm will last for 30 seconds.
In the event the alarm is triggered and remains triggered continuously by the same sensor or input during a single arming cycle,
that sensor or input will be automatically bypassed until the next time the system is armed.
If the shock sensor detects a light impact to the vehicle, or the optional sensor’s warn-away zone is disturbed, the siren will chirp
5 times as a warning indication. If the heavy impact is detected, the siren shall sound continously with flashing the parking light
at the same time.
3. REMOTE DISARMING
To disarm the system:
Press button 2.
The siren will chirp twice. The doors will unlock. The parking lights will flash twice. The dome light will turn on. The led will
turn off.
z During disarming, if the system is triggered while away from the vehicle, the siren will chirp 3 times, the parking lights will
that sensor or input will be automatically bypassed until the next time the system is armed.
If the shock sensor detects a light impact to the vehicle, or the optional sensor’s warn-away zone is disturbed, the siren will chirp
5 times as a warning indication. If the heavy impact is detected, the siren shall sound continously with flashing the parking light
at the same time.
3. REMOTE DISARMING
To disarm the system:
Press button 2.
The siren will chirp twice. The doors will unlock. The parking lights will flash twice. The dome light will turn on. The led will
turn off.
z During disarming, if the system is triggered while away from the vehicle, the siren will chirp 3 times, the parking lights will
flash 3 times, and the led will flash to indicate triggered zone. See tamper alert for zone listing.
4. TAMPER ALERT
If the system is triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning
on the ignition. The LED indication will repeat 1 minute. LED Flashes:
1 flash=optional sensor
2 flashes=shock sensor
3 flashes=not used
4 flashes=door
5 flashes=trunk
10 flashes=main power interrupt or system was reset
example: flash-flash-pause-flash-flash-pause=shock sensor
5. SILENT ARMING/DISARMING
The system can be programmed to operate without Arm and Disarm chirp indications. When programmed for full-time silent
operation, the siren will sound when the system is triggered. And when the auto rearming and passive arming are working, the
siren shall chirp once too when the system gets armed.
The system is also capable of temporary silent operation if desired. Pressing the button 3 before Arming or Disarming the system
will bypass the chirp confirmations and allow one-time silent operation.
Note: The open zone warning chirps will not be bypassed when system is Armed
6. PASSIVE ARMING
When programmed for the optional Passive Arming feature, the system arms itself automatically, each time the ignition is turned
off and all of the doors, hood, and trunk are closed. (select programming #2 for passive arming or passive arming w/countdown)
To start the Passive Arming Process:
1) Turn off the ignition.
If the system is triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning
on the ignition. The LED indication will repeat 1 minute. LED Flashes:
1 flash=optional sensor
2 flashes=shock sensor
3 flashes=not used
4 flashes=door
5 flashes=trunk
10 flashes=main power interrupt or system was reset
example: flash-flash-pause-flash-flash-pause=shock sensor
5. SILENT ARMING/DISARMING
The system can be programmed to operate without Arm and Disarm chirp indications. When programmed for full-time silent
operation, the siren will sound when the system is triggered. And when the auto rearming and passive arming are working, the
siren shall chirp once too when the system gets armed.
The system is also capable of temporary silent operation if desired. Pressing the button 3 before Arming or Disarming the system
will bypass the chirp confirmations and allow one-time silent operation.
Note: The open zone warning chirps will not be bypassed when system is Armed
6. PASSIVE ARMING
When programmed for the optional Passive Arming feature, the system arms itself automatically, each time the ignition is turned
off and all of the doors, hood, and trunk are closed. (select programming #2 for passive arming or passive arming w/countdown)
To start the Passive Arming Process:
1) Turn off the ignition.
*
2) Open the door and exit the vehicle.
Once all doors are closed and the dome light is off, the LED will begin flashing rapidly.
3) After 30 seconds:
The siren will chirp once. (no matter whether #14 arming chirp is programmed silent or normal, it always chirps once when