Guangzhou Chiyuan Electronic Co. Ltd. N-8C User Manual
R/C Introduction Manual
R/C Introduction Manual
4
3
2.3 D/R & EXP
!
Function
Dual rates are available for elevator and rudder channels of RC helicopters.
!
Operation
1. Press “ ” to entry the menu – Roll“ ” or “ ”select the function (D/R & Exp) in
the list Press “ ” to set the function and return to the previous menu.
2. Roll “ ” or “ ” to select ELEV and AILE to set the data.
3. ELEV setting ---- ‘ELEV’ is displayed
Once the Elevator D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ”
to increase or decrease the data.(2.3.1)
Once the Elevator D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ”
to increase or decrease the data.(2.3.2)
4. AILE setting ---- ‘AILE” is displayed
Once the Aileron D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ” to
increase or decrease the data. (2.3.3)
Once the Aileron D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ”
to increase or decrease the data. (2.3.4)
5.Press “ ” to save and return to the previous menu.
the list Press “ ” to set the function and return to the previous menu.
2. Roll “ ” or “ ” to select ELEV and AILE to set the data.
3. ELEV setting ---- ‘ELEV’ is displayed
Once the Elevator D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ”
to increase or decrease the data.(2.3.1)
Once the Elevator D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ”
to increase or decrease the data.(2.3.2)
4. AILE setting ---- ‘AILE” is displayed
Once the Aileron D/R switch is on/up, the data displayed is ‘Pos 0’. Use “ ” or “ ” to
increase or decrease the data. (2.3.3)
Once the Aileron D/R switch is off/down, the data displayed is ‘Pos 1’. Use “ ” or “ ”
to increase or decrease the data. (2.3.4)
5.Press “ ” to save and return to the previous menu.
[D/R&EXP]
[D/R&EXP]
AILE
AILE
Pos0
Pos0
Pos0
79%
79%
79%
D/R
LIN
LIN
D/R
LIN
LIN
[D/R&EXP]
[D/R&EXP]
AILE
AILE
Pos1
Pos1
Pos1
42%
42%
42%
D/R
LIN
LIN
D/R
LIN
LIN
[D/R&EXP]
[D/R&EXP]
ELEV
ELEV
Pos0
Pos0
Pos0
79%
79%
79%
D/R
LIN
LIN
D/R
LIN
LIN
[D/R&EXP]
[D/R&EXP]
ELEV
ELEV
Pos1
Pos1
Pos1
42%
42%
42%
D/R
LIN
LIN
D/R
LIN
LIN
(2.3.1)
(2.3.1)
(2.3.2)
(2.3.2)
(2.3.3)
(2.3.3)
(2.3.4)
(2.3.4)
2.4 Rev. SW
CH 1 2 3 4 5 6 7 8
CH 1 2 3 4 5 6 7 8
R
R
N
N
[REV.SW]
[REV.SW]
THRO
THRO
CH 1 2 3 4 5 6 7 8
CH 1 2 3 4 5 6 7 8
R
R
N
N
[REV.SW]
[REV.SW]
AUX3
AUX3
CH 1 2 3 4 5 6 7 8
CH 1 2 3 4 5 6 7 8
R
R
N
N
[REV.SW]
[REV.SW]
ELEV
ELEV
!
Function
The Reverse switch is to change the servo for channel direction.
!
Operation
1.Select ‘REV. SW’ and entry the interface.
2.Use “ ” or “ ” to select the channel arrow position. Press “ ” to reverse the
channel; press “ ” to the normal status.
3.Press“ ” to save and return to the previous menu.
2.Use “ ” or “ ” to select the channel arrow position. Press “ ” to reverse the
channel; press “ ” to the normal status.
3.Press“ ” to save and return to the previous menu.
2.2 Function List
"[FUNC.LIST]"
" D/R & EXP"
Dual Rate
" Rev. SW"
" Sub Trim"
Sub Trim
" Trvl ADJ."
Travel Adjustment
" Swash Mix"
Swash Mixing
" Swash TYP"
Swash Type
" Stick Mode"
Stick Mode
" Thro Curv"
Throttle Curve
" Pit Curv"
PIT. Curve
" Planes"
Planes
" Clear"
Clear
" Gyro Sens"
Gyro Sensitivity
" Idel Thro"
Idle Throttle
" Idel Pith"
Idle Pitch
"PLANE TYPE" PLANE TYPE
" Exit"
2.1 Menu
!
It is a default setting of helicopter in Model Type initially.
!
When the voltage displayed is 8.6V below, the number will be flashed and simultaneously
with warning.
with warning.
U
:
U
:
11.5v
11.5v
8 Channel R/C
8 Channel R/C
PPM/FM
PPM/FM
Channel Type
Channel Type
Model Type
Voltage
Voltage
Modulation Type
Modulation Type
Reversing Switch
Reversing Switch
T PCA RE
O
T PCA RE
O
Exit