Konica Minolta A09N User Manual
Safety Information Guide Authentication Unit (IC Card Type AU-201)
A09N-9
554-00
Carefully read this information, and then store it in a safe place.
•
Before using this device, carefully read this information and follow it to
operate the device correctly.
operate the device correctly.
•
After reading this information, store it in the designated holder with the
warranty.
warranty.
■ Important information
•
The reprinting or reproduction of the content of this publication, either in
part or in full, is prohibited without prior permission.
part or in full, is prohibited without prior permission.
•
The content of this publication is subject to change without notice.
•
This publication was created with careful attention to content; however, if
inaccuracies or errors are noticed, please contact your sales represen-
tative.
inaccuracies or errors are noticed, please contact your sales represen-
tative.
•
The marketing and authorization to use the KONICA MINOLTA BUSI-
NESS TECHNOLOGIES, INC. product mentioned in this information are
provided entirely on an
NESS TECHNOLOGIES, INC. product mentioned in this information are
provided entirely on an
“
as is
”
basis.
•
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. assumes no
responsibility for any damage (including lost profits or other related dam-
ages) caused by this product or its use as a result of operations not
described in this information. For disclaimers and warranty and liability
details, refer to the User's Guide Authentication Unit (IC Card Type AU-
201).
responsibility for any damage (including lost profits or other related dam-
ages) caused by this product or its use as a result of operations not
described in this information. For disclaimers and warranty and liability
details, refer to the User's Guide Authentication Unit (IC Card Type AU-
201).
•
This product is designed, manufactured and intended for general busi-
ness use. Do not use it for applications requiring high reliability and
which may have an extreme impact on lives and property. (Applications
requiring high reliability: Chemical plant management, medical equip-
ment management and emergency communications management)
ness use. Do not use it for applications requiring high reliability and
which may have an extreme impact on lives and property. (Applications
requiring high reliability: Chemical plant management, medical equip-
ment management and emergency communications management)
•
Use with other authentication devices is not guaranteed.
•
In order to incorporate improvements in the product, the specifications
concerning this product are subject to change without notice.
concerning this product are subject to change without notice.
■ For safe use
■ Regulation notices
CE Marking (Declaration of Conformity) for Users of the
European Union (EU)
European Union (EU)
This product complies with the following EU directives:
89/336/EEC, 93/68/EEC, 73/23/EEC, 93/68/EEC and 99/5/EEC directives.
89/336/EEC, 93/68/EEC, 73/23/EEC, 93/68/EEC and 99/5/EEC directives.
This declaration is valid for the area of the European Union.
This device must be used with a USB cable packed. The use of the others
cables is likely to result in interference with radio communications and is
prohibited under CISPR rules and local rules.
cables is likely to result in interference with radio communications and is
prohibited under CISPR rules and local rules.
USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY
DEVICES (For U.S.A. Users)
DEVICES (For U.S.A. Users)
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interface by one or more of the following measures:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interface by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help
WARNING:
The design and production of this unit conform to FCC regulations, and
any changes or modifications must be registered with the FCC and are
subject to FCC control. Any changes made by the purchaser or user
without first contacting the manufacturer will be subject to penalty under
FCC regulations.
The design and production of this unit conform to FCC regulations, and
any changes or modifications must be registered with the FCC and are
subject to FCC control. Any changes made by the purchaser or user
without first contacting the manufacturer will be subject to penalty under
FCC regulations.
INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-
003 ISSUE 4) (For Canada Users)
003 ISSUE 4) (For Canada Users)
(This device complies with RSS-Gen of IC Rules.) Operation is subject to
the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference
that may cause undesired operation of this device.
the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference
that may cause undesired operation of this device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
du Canada.
For EU member states only
This symbol means: Do not dispose of this
product together with your household
waste!
product together with your household
waste!
Please refer to the information of your local
community or contact our dealers regrading
the proper handling of end-of-life electric
and electronic equipments. Recycling of this
product will help to conserve natural
resources and prevent potential negative
consequences for the environment and
human health caused by inappropriate
waste handling.
community or contact our dealers regrading
the proper handling of end-of-life electric
and electronic equipments. Recycling of this
product will help to conserve natural
resources and prevent potential negative
consequences for the environment and
human health caused by inappropriate
waste handling.
•
Do not this product near water, otherwise it may be dam-
aged.
aged.
•
Do not cut, damage, modify or forcefully bend the USB
cable. A malfunction may occur as a result of a damaged or
cut USB cable.
cable. A malfunction may occur as a result of a damaged or
cut USB cable.
•
Do not disassembly this device, otherwise it may be dam-
aged.
aged.
FCC: Declaration of Conformity
Product Type
Authentication Unit (IC Card Type)
Product Name
AU-201
(This device complies with Part 15 of the FCC Rules.) Operation
is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation
of this device.
is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation
of this device.