Wilson Electronics LLC 460022 User Manual
8
ENGLISH
Need help?
www.weBoost.com
Customer Support 866-294-1660
Mon.- Fri. Hours: 7 am to 6 pm MST
Signal Booster Specifications
Drive 4G-S
Model Number
460022
Connectors
SMA-Female
Antenna Impedance
50 Ohms
Frequency
698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Passband Gain (nominal)
700
MHz
Band12/17
16.7
700
MHz
Band13
15.7
800
MHz
16.0
1700/2100
MHz
15.7
1900
MHz
15.1
20 dB Bandwidth (MHz)
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700/2100
MHz
1900
MHz
Typical
Maximum
32.7
36.9
34.0
37.1
41.8
43.8
88.2
90.4
84.5
85.5
Power output for single cell
phone (Uplink) dBm
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700
MHz
1900
MHz
24.28
24.35
24.44
25.14
24.25
Power output for single cell
phone (Downlink) dBm
700
MHz
Band12/17
700
MHz
Band13
800
MHz
2100
MHz
1900
MHz
10.84
11.23
11.72
12.35
10.96
Power output for multiple
received channels (Uplink) dBm
No. Tones
700
MHz
Band12/17
700
MHz
Band13
800
MHz
1700
MHz
1900
MHz
2
24.8
22.5
20.7
21.4
22.5
3
21.2
19.0
17.1
17.9
18.9
4
18.7
16.5
14.6
15.4
16.4
5
16.8
14.6
12.7
13.5
14.5
6
15.2
13.0
11.1
11.9
12.9
Power output for multiple
received channels
(Downlinklink) dBm
No. Tones
700
MHz
Band12/17
700
MHz
Band13
800
MHz
2100
MHz
1900
MHz
2
13.0
12.9
13.5
12.5
10.9
3
9.4
9.4
10.0
9.0
7.4
4
6.9
6.9
7.5
6.5
4.9
5
5.0
4.9
5.5
4.6
2.9
6
3.4
3.4
3.9
3.0
1.3
Noise Figure
5 dB nominal
Isolation
> 40 dB
Power Requirements
5.5 V 2 A
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory
reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase
coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected.
If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn
the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1
minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually
restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s
microprocessor.
The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are
present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to
adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the
device.