Manualsbrain.com
  1. Manuals
  2. Brands
  3. The Watt Stopper Inc.
  4. TDHHR
  5. User Manual

The Watt Stopper Inc. TDHHR User Manual

Download
Page of 5
2, 4 
3 
3 
Ø 
× 
Note: when you 
see Ú in the 
instructions, press 
the top and the 
bottom of the 
device rocker for 2 
seconds 
3 
 
 
 
 
 
 
How to install and use the 
radioMiro
TM
 room remote 
control 
 
English 
Read and retain these instructions 
 
Français 
 
 
Español 
 
 
Ready? 
Application  
 
 
 
 
 
 
For more 
information
 on designing, 
installing and using 
radioMiro
TM
 
systems, and for expert 
technical 
help
, visit our web site at 
www.passandseymour.com/miro
 
Use the radioMiro
TM
 room remote control in 
a room with any number of radioMiro
TM
 
dimming or non-dim devices, normally 
including one or more wall-mounting 
radioMiro
TM
 room preset controllers. 
The radioMiro
TM
 room remote control gives 
you fingertip control of individual circuits, 
presets and overall room light level, in a 
convenient unit that looks and feels good on 
the coffee table or by the bed! 
 
Note: for whole-house control, use a 
radioMiro
TM
 whole-house preset controller or 
handheld remote. 
 
 
 
Batteries  
 
 
 
 
 
 
 
 
 
 
Figure 1 
1.  Remove the battery cover in the base of 
the unit, and install the three AAA cells 
provided in accordance with the diagram 
in the battery compartment. 
2.  Replace the battery cover and press any 
button – the status LED will be green if 
the batteries are good 
3.  When the batteries start to lose their 
charge, the status LED will blink red, 
indicating that new batteries are 
required.  
4.  Note that to conserve battery life, the 
remote ‘goes to sleep’ when it has not 
been used for one minute, and the status 
LED goes out. Pressing any button while 
the remote is asleep causes the remote 
to ‘wake up’, ready for use. 
  
 
 
Get Set… 
Configuration  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2
 
To prevent interference between neighboring 
systems, radioMiro
TM
 devices must acquire 
a unique house ID before use. It’s simple! 
1.  With all devices installed and energized, 
check that every radioMiro
TM
 device is 
showing a yellow LED. If not, check that 
the circuit breaker is on and that the 
device is correctly installed.  
2.  All devices in a home must be ‘bound’ to 
the same home ID. For a new 
radioMiro
TM
 installation, simultaneously 
press and hold the top and bottom (Ú) of 
any device paddle for 2 seconds. Its LED 
flashes yellow, indicating that it has 
acquired a unique House ID. 
3.  Check that all other radioMiro
TM
 device 
LEDs are flashing green, indicating that 
they have acquired the same House ID.  
4.  Return to the first device, and press Ú 
again for 2 seconds. All device LEDs 
revert to green, indicating that house 
binding is complete. 
Note: if you’re adding the device to an 
existing radioMiro
TM
 installation, simply 
press and hold Ú on any previously bound 
device for 2 seconds to start the procedure, 
verify that the newly added device LED is 
flashing green, indicating that it has acquired 
the House ID. Press and hold Ú for 2 
seconds again on the same previously 
installed device to terminate. 
Handheld devices will not respond to a 
binding signal when they are not in use. 
 
 
Need Graphic - 
Battery 
installation 
placeholder 
Status 
LED