The Watt Stopper Inc. TDKFOB User Manual
WARRANTY INFORMATION
Watt Stopper/Legrand warranties its products to be free of
defects in materials and workmanship for a period of five (5)
years. There are no obligations or liabilities on the part of Watt
Stopper/Legrand for consequential damages arising out of, or
in connection with, the use or performance of this product or
other indirect damages with respect to loss of property, revenue
or profit, or cost of removal, installation or reinstallation.
defects in materials and workmanship for a period of five (5)
years. There are no obligations or liabilities on the part of Watt
Stopper/Legrand for consequential damages arising out of, or
in connection with, the use or performance of this product or
other indirect damages with respect to loss of property, revenue
or profit, or cost of removal, installation or reinstallation.
2800 De La Cruz Boulevard, Santa Clara, CA 95050
Technical Support: 800.879.8585
www.wattstopper.com
07071r1 6/2007
FCC Notice
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
for help.
Caution: Any changes or modifications to this device not
explicitly approved by Watt Stopper/Legrand could void your
authority to operate this equipment.
explicitly approved by Watt Stopper/Legrand could void your
authority to operate this equipment.
5.
Reassemble the unit as shown in the drawing below then
snap the housing together. Test the buttons and make
sure you get the appropriate soft click when you press
them.
snap the housing together. Test the buttons and make
sure you get the appropriate soft click when you press
them.
TESTING
After completing the MKFOB setup, you can test scene recall
by pressing a button. You should hear a soft click when
you press each button. Scene recall works best with an
immediate release of the button. The LED should come on
and be green then turn off a second or two after you release
the button.
by pressing a button. You should hear a soft click when
you press each button. Scene recall works best with an
immediate release of the button. The LED should come on
and be green then turn off a second or two after you release
the button.
TROUBLESHOOTING
During Set House ID, the LED is not flashing on some
Wireless devices.
Wireless devices.
• If an LED is solid green before initiating house ID binding:
The device already has another house ID. Reset
it to the factory default so that it can be bound to
the desired house ID. Resetting to factory defaults
is described in the “I need to start over” issue.
the desired house ID. Resetting to factory defaults
is described in the “I need to start over” issue.
• If LED is solid yellow after initiating house ID binding:
The device may be out of range of the initiating device.
Move the MKFOB closer to the initiating device. It may
be necessary to add a MRR2 Repeater if reception
to a particular area of the house is blocked.
be necessary to add a MRR2 Repeater if reception
to a particular area of the house is blocked.
The MKFOB won’t accept the House ID binding and it will
not initiate a binding.
not initiate a binding.
• See “There is no click ...” below.
There is no click when I press a button.
The key membrane inside the MKFOB housing may be
out of position. Open the housing using a coin as shown
in the Battery Replacement section. Reposition the
membrane so that the back side
of the keys make solid contact
with the rectangular button
contacts on the printed circuit
board. Two raised hard black
plastic ribs on the inside of the
housing between the button cut-
outs should protrude through
the slits between the buttons
on the soft rubber membrane.
in the Battery Replacement section. Reposition the
membrane so that the back side
of the keys make solid contact
with the rectangular button
contacts on the printed circuit
board. Two raised hard black
plastic ribs on the inside of the
housing between the button cut-
outs should protrude through
the slits between the buttons
on the soft rubber membrane.
Alignment
Ribs
Ribs
A device that is included in a scene does not respond
appropriately when I invoke the scene from the MKFOB.
appropriately when I invoke the scene from the MKFOB.
The non-responsive device may be out of range of the
MKFOB. Move the MKFOB closer to the device and
invoke the scene from the MKFOB. If the device responds
appropriately from this distance, it may be necessary to
install an MRR2 Repeater at a location that is within range
of the location from which the MKFOB is typically operated.
invoke the scene from the MKFOB. If the device responds
appropriately from this distance, it may be necessary to
install an MRR2 Repeater at a location that is within range
of the location from which the MKFOB is typically operated.
I need to start over.
You can reset any wireless device to factory default settings
by pressing and holding its binding activation buttons until
its LED changes to solid yellow (approximately 10 seconds).
its LED changes to solid yellow (approximately 10 seconds).
For the MKFOB, the binding activation buttons are 1
and 2. During the process, the LED fl ashes yellow and
when the reset is complete, it changes to solid yellow.
The yellow LED stays lit for approximately one minute
as it waits to hear a binding message. The device can
then be reconfi gured, exactly like any new device.
To set the House ID in the MKFOB, initiate a binding
from any previously bound device in the house.
when the reset is complete, it changes to solid yellow.
The yellow LED stays lit for approximately one minute
as it waits to hear a binding message. The device can
then be reconfi gured, exactly like any new device.
To set the House ID in the MKFOB, initiate a binding
from any previously bound device in the house.
LED
Key-chain
Loop
Printed Circuit
Board (front)
Back Housing, inside chamber
Please
Recycle