Linksys DMP100 User Manual

Page of 36
Regulatory Information
16
Wireless Home Audio
Player/Wireless-N Music Extender
Regulatory Information
Safety Warning Statement
 
WARNING:
 
This 
exclamation 
point 
indicates  that  there  is  a  caution  or 
warning  of  potential  risk  of  bodily  injury  
and/or it is something that could damage your  
property or product.
 
WARNING:
 Do not use this product near water, 
for example, near bath tube, kitchen sink, in a 
wet basement or near a swimming pool.
California Lead Warning Statement
 
WARNING:
 This product contains lead, known 
to  the  State  of  California  to  cause  cancer,  and 
birth defects or other reproductive harm. Wash 
hands after handling.
FCC RF Exposure Statement
This  equipment  complies  with  FCC  radiation  exposure 
limits  set  forth  for  an  uncontrolled  environment.  This 
equipment  should  be  installed  and  operated  with 
minimum distance 20 cm between the radiator and your 
body. This transmitter must not be co-located or operating 
in conjunction with any other antenna.
Canadian RF Exposure Statement
This  equipment  is  in  conformity  with  the  IC  radiation 
exposure limits set forth for an uncontrolled environment. 
This device must be installed and used at a distance of at 
least 20 cm (8 in) between the antenna and the body of 
the  user. The  transmitter  should  not  be  placed  close  to 
another  antenna  or  another  transmitter,  or  to  function 
with another antenna or another transmitter.
Avis d’Industrie Canada concernant 
l’exposition aux radiofréquences
Cet appareil numérique est conforme aux limites établies 
par IC en matière d’exposition aux radiofréquences dans 
un  environnement  non  contrôlé.  Ce  matériel  doit  être 
installé et utilisé à une distance d’au moins 20 cm (8 in) 
entre l’antenne et le corps de l’utilisateur. L’émetteur ne 
doit pas être placé près d’une autre antenne ou d’un autre 
émetteur, ou fonctionner avec une autre antenne ou un 
autre émetteur.
Australian RF Exposure Statement
 
WARNING:
 To ensure compliance with exposure 
limits  to  radiofrequency  fields,  the  antenna  of 
the device should be no closer than 20 cm from 
the body during use.
Approved Antenna Information
DMP100 player with Dipole type antenna and maximum 
antenna gain is 3.5dBi in 5 GHz band and 1.5dBi in 2.4GHz 
band.
FCC Part15 Class B Statement
This  device  complies  with  Part  15  of  the  FCC  Rules. 
Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this 
device  must  accept  any  interference  received,  including 
interference that may cause undesired operation. 
This  product  has  been  tested  and  complies  with  the 
specifications for a Class B digital device, pursuant to Part 
15 of the FCC Rules. These limits are designed to provide 
reasonable  protection  against  harmful  interference  in 
a  residential  installation.  This  equipment  generates, 
uses, and can radiate radio frequency energy and, if not 
installed  and  used  according  to  the  instructions,  may 
cause  harmful  interference  to  radio  communications. 
However, there is no guarantee that interference will not 
occur  in  a  particular  installation.  If  this  equipment  does 
cause harmful interference to radio or television reception, 
which is found by turning the equipment off and on, the 
user  is  encouraged  to  try  to  correct  the  interference  by 
one or more of the following measures:
Reorient or relocate the receiving antenna
 
Increase  the  separation  between  the  equipment  or 
 
devices
Connect  the  equipment  to  an  outlet  other  than  the 
 
receiver’s
Consult a dealer or an experienced radio/TV technician 
 
for assistance
FCC Caution
Any changes or modifications not expressly approved by 
the party responsible for compliance could void the user’s 
authority to operate this equipment.
For operation within 5.150-5.250 GHz frequency range, it 
is restricted to indoor environment.
The  availability  of  some  specific  and/or  operational 
frequency bands are country dependent and are firmware 
programmed  at  the  factory  to  match  the  intended 
destination. The firmware setting is not accessible by the 
end user.