NINGBO BAIHUANG ELECTRIC APPLIANCES CO. LTD. BHD9829U User Manual
Remote Control Lamp Holder
Self-Learning
Model No.: BHD9829U
Please read and understand the instruction manual
carefully before use!
Features:
•
Each lamp socket can be manually switched or via the
handy transmitter.
•
Individual ON and OFF function from the remote transmitter.
•
Easy to use and operate – use one transmitter to control a
single lamp socket receiver or program more than one
transmitters to each lamp socket.
single lamp socket receiver or program more than one
transmitters to each lamp socket.
•
Self-Learning type, any one transmitter and lamp socket
can be programmed with each other, so extra lamp sockets
and remote controls can be purchased separately and
matched to the existing unit.
can be programmed with each other, so extra lamp sockets
and remote controls can be purchased separately and
matched to the existing unit.
•
Very lower standby power consumption, reduce energy
cost when not be working
•
The lamp socket will remain ‘OFF’ after a power cut,
saving energy
Product:
This product consists of one or two remote transmitters with
ON and OFF function and several lamp sockets.
ON and OFF function and several lamp sockets.
Re-Programming/Self-Learning Operation:
The lamp sockets are pre-programmed for immediate use,
but maybe there are few units are not pre-programmed or
programmed incorrectly, or you want to change the pre-set
configuration to meet your needs. Please follow the steps
below:
but maybe there are few units are not pre-programmed or
programmed incorrectly, or you want to change the pre-set
configuration to meet your needs. Please follow the steps
below:
•
Restting an lamp socket as per mentioned sections above
firstly
firstly
•
Press the program button until indicator light starts to blink
Resetting an Lamp Socket (Cancel programming):
To remove an lamp socket from all transmitter parings:
•
Unscrew the lamp connected to the remote lamp socket.
•
Turn the power off.
•
Press the program button.
•
Turn the power on again while continuing to press program
button for approximately 5 seconds until the indicator
button for approximately 5 seconds until the indicator
begins to flash.
•
Program reset is successful when the indicator on lamp
socket flashes several times and stops blinking
socket flashes several times and stops blinking
•
Release the program button, press the ‘ON’ or ‘OFF’ button
for any desired number on the transmitter.
for any desired number on the transmitter.
•
Programming /paring is successful when indicator light
stops blinking.
stops blinking.
Note: You may repeat the re-programming steps to assign
up to more lamp sockets to a single pair of buttons
on transmitter to simultaneously control multiple
lamps one time.
on transmitter to simultaneously control multiple
lamps one time.
Technical data:
120V~/60Hz
433.92MHz
DC12V (23A) Alkaline battery
60W
80feet (free area)
Working Voltage for socket
Transmission frequency
Remote control distance
Max.load power
Power for transmitter
Installation:
•
Install 1pc 12V(23A) Alkaline battery in the transmitter’s
battery compartment, making sure the polarity + / - of the
battery compartment, making sure the polarity + / - of the
battery is correct.
•
Plug each lamp socket into a existing light socket and
screw a lamp into each lamp socket.
screw a lamp into each lamp socket.
•
Push each ON or OFF button on transmitter will turn on or
off the corresponding lamp socket accordingly.
off the corresponding lamp socket accordingly.
Product illust ration:
Lamp socket
ON
OFF
1
2
3
4
5
Indicator
Transmitter BH-V
ON
OFF
1
2
3
Indicator
Transmitter BH-U
Notes:
•
The lamp sockets are intended for indoor use only.
•
The wireless range may be shortened by other electronic
devices, appliances, walls, and other physical barriers.
•
Avoid exposing to high-temperature sources, direct
sunlight, or exposure to moisture.
•
DO NOT exceed the maximum load of approximately
60W.
•
The lamp sockets are best used in areas with proper air
circulation.
•
For your safety, make sure the batteries within the
transmitters are correctly installed before use.
•
DO NOT dispose any part of this product in a fire.
•
This device is not intended for use in areas with high
humidity, such as bathrooms.
•
For best performance, regular change the batteries in the
remote control.
•
Discard all parts of this product in accordance with local
environmental regulations.Do not dispose in regular
household waste.
•
If the remote is not in use for an extended period of time,
remove batteries.
•
When cleaning, use a dry or damp cleaning cloth to wipe
the lamp socket and remote surfaces.
Note: Extra buttons on transmitters can be used with
additional lamp sockets.
Troubleshooting:
In the case that one lamp socket is unresponsive to a
remote control, follow the steps below to resolve the
issue:
issue:
•
If the lamp socket is unresponsive to the remote control,
please refer to the ‘Resetting an lamp socket’ and ‘Re-
programming operation’ sections in the manual.
• Replace the remote batteries with new 12V (23A) batteries.
• Replace the remote batteries with new 12V (23A) batteries.
Low battery power may decrease readable wireless remote
range.
range.
•
Make sure the lamp socket and lamp are properly
connected and powered on.
connected and powered on.
•
Make sure that the lamp socket is placed in an area with
proper air circulation without overheating.
proper air circulation without overheating.
•
Make sure the maximum load approximately 60W is not
being exceed. If so, unscrew the lamp from the lamp
socket immediately.
being exceed. If so, unscrew the lamp from the lamp
socket immediately.
• ‘
Resetting an lamp socket’ is always prior to ‘Re-
programming operation’ when you want to make some
changes.
changes.
Should you have any issues or questions regarding your
New product, feel free to contact our Customer Support
Team. Your satisfaction is ours.
New product, feel free to contact our Customer Support
Team. Your satisfaction is ours.
Indicator
program
button
FCC Warning:
Changes or modifications to this unit not expressly approved by the
party responsible for compliance will void the user’s authority to
operate the equipment. Any change to the equipment will void FCC
grant.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV
technician for help.