Leviton Manufacturing Co. Inc. VRSDC User Manual

Preparing and connecting wires:

This receptacle can be wired using side wire terminal screws or

through backwire openings. Choose appropriate wire stripping

specifications accordingly.

WARNING:

TO AVOID FIRE SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is off

before wiring!

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble any of

these configurations, consult a qualified electrician.

WARNINGS AND CAUTIONS

• To be installed and/or used in accordance with electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• To ensure that there is adequate room for wires, we recommend using at a minimum 3-1/2 inch deep wallboxes. For single-gang applications, this would be at a

minimum an 18-cubic inch wallbox.

WARNINGS AND CAUTIONS

• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

• Maximum wire length cannot exceed 300 ft (90 m).

• Use this device with copper or copper clad wire only.

Duplex Receptacle (Top Controlled)

Scene Capable Receptacle

Cat. No. VRR15-1L - 15A - 125VAC, 60Hz

Incandescent-1800W – Magnetic Low-Voltage-1800VA (1440W)

Electronic Low-Voltage-1800W – Fluorescent-1800VA – Supplemental-1/2 HP

INSTALLATION INSTRUCTIONS

DI-000-VRR15-02A

Tools needed to install your Receptacle

Slotted/Phillips Screwdriver

Electrical Tape

Pliers

Pencil

Cutters

Ruler

Changing the color of your Receptacle:

Your Receptacle includes three color options. The Receptacle ships with the

White frame attached. To change color of frame, proceed as follows:

INSTALLING YOUR RECEPTACLE

NOTE: Use check boxes when Steps are completed.

OFF

Step 1

Single Pole
1. Line (Hot)

2. Neutral

3. Ground

Step 2

Single Pole Wiring Application:

Step 3

• Make sure that the ends of the wires from the wall box are

straight (cut if necessary).

• Remove insulation from each wire in the wall box as shown.

5/8"

(1.6 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Side Wire Connection

Side wire terminals accept #14-12

AWG solid copper wire only.

Back Wire (either hole may be used)

Back wire openings accept #14-12

AWG solid copper wire only.

WIRING RECEPTACLE:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot wall box wire to terminal screw marked "LINE".

• Line Neutral wall box wire to terminal screw marked "NEUTRAL".

• Proceed to Step 5.

Leviton’s Vizia RF +™ Z-Wave

components are designed to communicate

with each other via Radio Frequency (RF) to provide remote control of

your lighting. Using RF technology allows Leviton to provide the greatest

signal integrity possible. Each module in Leviton’s Vizia RF +™ component

line is a Z-Wave

enabled device. In a Z-Wave

network, each device is

designed to act as a router. These routers will re-transmit the RF signal

from one device to another until the intended device is reached. This

ensures that the signal is received by its intended device by routing

the signal around obstacles and radio dead spots. The Scene Capable

Electronic Receptacle is compatible with most Z-Wave

enabled networks,

from different manufacturers and can also be used with other devices

displaying the Z-Wave

logo.

CAUTION:

Remember to exercise good common sense when using the Timer features

of your Remote – especially when scheduling unattended devices. There

can be some unexpected consequences if not used with care. For example,

an empty coffee pot can be remotely turned on. If that should happen,

your coffee pot could be damaged from overheating. If an electric heater

is turned on by remote control while clothing is draped over it, a fire could

result. DO NOT USE the remote for the control of high power heating

appliances such as portable heaters.

• Receptacle ON/OFF

• Scene Capable

• ON/OFF LED

• Two way communication

• RF reliability

• Ease of installation – No new wiring

• Compatible with other Z-Wave

enabled devices

FEATURES

INTRODUCTION

Testing your Receptacle prior to mounting in

wall box:

Receptacle Mounting:

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.

• Restore power at circuit breaker or fuse.

• Locator light should turn ON.

If locator light does not turn ON, refer to the TROUBLESHOOTING

section.

Step 5

• Position all wires to provide room in outlet wall box for device.

• Partially screw in mounting screws in wall box mounting holes.

NOTE: Dress wires with a bend as shown in diagram in order to

relieve stress when mounting device.

Step 6

Restore Power:

Restore power at circuit breaker or fuse.

Installation is complete.

Step 7

Neutral (Silver)

Line (Black)

Green

Ground

CONTROLLED

Push in side

at tab to release

Line up tabs and

press in sides one at a time

to attach

Step 4

CONTROLLED

Installation may now be completed by tightening

mounting screws into wall box. Attach wallplate.