My Music Group Limited E06 User Manual

(Purchase individually, not include in the set)

• Cell Phone with Bluetooth version lower than         will requir

4. Volume Down

2. Volume Up

1. Previous

3. Next

6. Charge

5. Power/Multi

7. Line-in 

This headset has an internal rechargeable battery. The battery must be fully 

charged before you  can start using the headset.

(charge time it approximately 2.5 hrs):

1. Connect the charger to the standard AC power socket.

2. Connect one end of the USB cable to the charger, and the other end to 

the charge interface of the headset (

6).

Red light ON − Charging

Red light OFF − Fully Charged

Via USB charging cable 
1. Connect the USB charging cable to the USB interface of the computer.

2. Connect the other end of the USB cable to the charger of the headset (

6).

Red light ON − Charging

Red light OFF − Fully Charged

PAIR THE HEADSET WITH A BLUETOOTH CELL PHONE

First, please make sure the bluetooth function is available for the cell phone.

Specific pairing procedures will be different depending on different cell phone. 

For detailed information, please refer to your cell phone’s User Guide.
1. Keep the distance between the cell phone and the headset within 3 feet.

2. To start pairing, make sure the headset is switched off. To do that, press and 

hold the multifunction key (

6) for about 5 seconds and release it until the 

alternative flash of red and green lights (one long and two short beeps 

will sound).

3. Switch on the headset by pressing and holding the multifunction key (

5) 

for about 3 seconds and release it until blue light flashes. 

4. Activate the bluetooth function of the cell phone, to search for the 

Bluetooth devices. After finishing the search, select “E06” in the device 

list displayed. 

5. Press “yes” or “enter” key to confirm the successful pairing in accordance 

with the hint of the cell phone.

6. After the successful connection, the blue light of the headset will flash 

quickly twice every four seconds.
Note:

e for password 

or PIN code entry: “oooo”.

Notes:  

• The pairing mode lasts for 2 minutes. The headset will automatically switch 

to standby mode if no pair is made with any devices over 2 minutes.
• If no device connection is made within 5 minutes of the headset being 

switched on, the headset will automatically be switched off to save power.
• After a successful pairing devices will memorize each. Therefore, no pairing 

will be needed next time.

1

2

3

4

5

6

NOTE: This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equi

pment generates uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a par ticular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following  measures:  

 

 

- Reorient or relocate the receiving antenna.  

- Increase the separation between the equipment and receiver.  

-Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

-Consult the dealer or an ex perienced radio/TV technician for help  

 

Changes or modifications not expressly approved by the party responsible for compliance  

could void the user's authority to operate the equipment.   This device complies with Part 

15 of the FCC Rules.  Operation is subject to the following two conditions:  

(1) this device may not cause harmful interference, and  

(2) this device must accept any interference received,  including interference that may 

cause undesired operation.  

 

 

V4.0