LUDA Elektronik AB 2007 User Manual
Image Device
TV System
TV System
PAL
NTSC
Effective Pixels
Sensing Area
Scanning System
Sync. System
Horizontal Sync Frequency
Sensing Area
Scanning System
Sync. System
Horizontal Sync Frequency
15.625 kHz
15.734 kHz
CAMERA SPECIFICATION
1/3" CMOS PC1089
728×488 pixels
4.6228mm×3.6112mm
2:1 Interlace
Internal
y
q
y
Vertical Sync Frequency
50 Hz
60 Hz
Video Output
Gamma Consumption
AGC
S/N Ratio
White Balance
Electronic Shutter
BLC
Operation Frequency:
Gamma Consumption
AGC
S/N Ratio
White Balance
Electronic Shutter
BLC
Operation Frequency:
1.0Vp-p, 75Ohm
0.45
Auto
Better than 48dB
Auto
Auto:1/60(NTSC)/1/50(PAL)～1/100,000 Seconds
Auto
2400-2483.5MHZ
p
q
y
Line of Sight Range:
Receiving Sensitivity:
Video Codec:
Frame Rate:
Output Power:
Spread SPECTRUM:
Delay:
RF Bit Rate:
Operating Temperature
Receiving Sensitivity:
Video Codec:
Frame Rate:
Output Power:
Spread SPECTRUM:
Delay:
RF Bit Rate:
Operating Temperature
2400 2483.5MHZ
120M
-89dBm
MPEG4
MPEG4
PAL: 25f/s NTSC: 30f/s
17dBm
FHSS
120ms
4Mbps
4Mbps
–20℃ ~ 70℃ RH95%MAX
Operating Temperature
Storage Temperature
Minimum Illumination
Power Supply
Night vision distance
Waterproof rating
Audio
Viewing Angle
Storage Temperature
Minimum Illumination
Power Supply
Night vision distance
Waterproof rating
Audio
Viewing Angle
–20℃ 70℃, RH95%MAX.
–30℃ ~ 80℃, RH95%MAX.
Auto pairing:
0Lux
DC10~32V
■8~10m □12~15m
IP69K
■ Yes □ No
■ 120° □ 92°
1. Choose the channel that needs to be set up, and the monitor display the
message
“PAIRING START 50” and a counter that counts down 50s.
2. Within the countdown, power the camera.
3. The monitor and cameras will synchronize themselves with each other after
the
camera is powered for 5s.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal” Repeat the pairing procedure
message
“PAIRING START 50” and a counter that counts down 50s.
2. Within the countdown, power the camera.
3. The monitor and cameras will synchronize themselves with each other after
the
camera is powered for 5s.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal” Repeat the pairing procedure
monitor displays the message No Signal . Repeat the pairing procedure.
Manually pairing:
1. Choose the channel that needs to be set up, and the monitor display the
message
“PAIRING START 50” and a counter that counts down 50s.
2. Press the pairing button on the power-on camera.
3. The monitor and cameras will synchronize themselves with each other.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal”. Repeat the pairing procedure.
Manually pairing:
1. Choose the channel that needs to be set up, and the monitor display the
message
“PAIRING START 50” and a counter that counts down 50s.
2. Press the pairing button on the power-on camera.
3. The monitor and cameras will synchronize themselves with each other.
For successful auto pairing, the picture appears. If pairing isunsuccessful, the
monitor displays the message “No Signal”. Repeat the pairing procedure.