Lancom Systems OAP-321-3G 61540 User Manual

LANCOM OAP-321-3G

Scope of features: as of LCOS version 8.5x

MIMO

MIMO technology is a technique which uses multiple transmitters to deliver multiple data streams via different spatial channels. 
LANCOM uses a 3 x 3 MIMO Configuration where 2 data streams are spread over 3 transmitters. Depending on the existing RF 
conditions the throughput is doubled with MIMO technology

40 MHz Channels

Two adjacent 20 MHz channels are combined to create a single 40 MHz channel. Depending on the existing RF Conditions 
channel bonding doubles the throughput.

MAC Aggregation and Block 
Acknowledgement

MAC Aggregation increase the 802.11 MAC efficiency by combining MAC data frames and sending it out with a single header. 
The receiver acknowledges the combined MAC frame with a Block Acknowledgement. Depending on existing RF conditions, this 
technique improves throughput by up to 20%.

Short Guard Interval

The guard interval is the time between OFDM symbols in the air. 802.11n gives the option for a shorter 400 nsec guard interval 
compared to the legacy 800 nsec guard interval. Under ideal RF conditions this increases the throughput by upto 10%

BFWA*

Support for Broadband Fixed Wireless Access in 5.8 GHz band with up to 4 Watt EIRP for WLAN point- to- point links according 
to the national regulations of your country, special antennas required

*) Note

The use of BFWA is subject to country specific regulation

WLAN access point

Infrastructure mode (autonomous operation or managed by LANCOM WLAN Controller)

WLAN bridge

Point- to- multipoint connection of up to 7 Ethernet LANs (mixed operation optional), broken link detection, blind mode, supports  
VLAN

When configuring Pt- to- Pt links, pre- configured names can be used as an alternative to MAC Adresses for creating a link. Rapid 
spanning- tree protocol to support redundant routes in Ethernet networks

WLAN router

Use of the LAN connector for simultaneous DSL over LAN, IP router, NAT/Reverse NAT (IP masquerading) DHCP server, DHCP 
client, DHCP relay server, DNS server, PPPoE client (incl.Multi- PPPoE), PPTP client and server, NetBIOS proxy, DynDNS client, 
NTP, port mapping, policy- based routing based on routing tags, tagging based on firewall rules, dynamic routing with RIPv2, 
VRRP

WLAN client

Transparent WLAN client mode for wireless Ethernet extensions, e.g. connecting PCs or printers by Ethernet; up to 64 MAC 
addresses. Automatic selection of a WLAN profile (max. 8) with individual access parameters depending on signal strength or 
priority

Supported standards

UMTS, HSPA+ (HSPA+ with up to 21 Mbps, HSUPA with up to 5.76 Mbps), Edge, and GPRS support

UMTS and HSxPA bands

850/900/1900/2100 MHz 

EDGE/GPRS bands

850/900/1800/1900 Mhz (EDGE up to max. 236kbps)

Diversity support

Receive diversity on the aux antenna

Stateful inspection firewall

Incoming/Outgoing Traffic inspection based on connection information. Trigger for firewall rules depending on backup status, 
e.g. simplified rule sets for low- bandwidth backup lines. Limitation of the number of sessions per remote site (ID)

Packet filter

Check based on the header information of an IP packet (IP or MAC source/destination addresses; source/destination ports, 
DiffServ attribute); remote- site dependant, direction dependant, bandwidth dependant

Extended port forwarding

Network Address Translation (NAT) based on protocol and WAN address, i.e. to make internal webservers accessible from WAN

N:N IP address mapping

N:N IP address mapping for translation of IP addresses or entire networks

Tagging

The firewall marks packets with routing tags, e.g. for policy- based routing

Actions

Forward, drop, reject, block sender address, close destination port, disconnect

Notification

Via e- mail, SYSLOG or SNMP trap

Traffic shaping

Dynamic bandwidth management with IP traffic shaping

Bandwidth reservation

Dynamic reservation of minimum and maximum bandwidths, totally or connection based, separate settings for send and receive 
directions. Setting relative bandwidth limits for QoS in percent. Bandwidth control and QoS also for UMTS connections

DiffServ/TOS

Priority queuing of packets based on DiffServ/TOS fields 

Packet- size control

Automatic packet- size control by fragmentation or Path Maximum Transmission Unit (PMTU) adjustment

Layer 2/Layer 3 tagging

Automatic or fixed translation of layer- 2 priority information (802.11p- marked Ethernet frames) to layer- 3 DiffServ attributes in 
routing mode. Translation from layer 3 to layer 2 with automatic recognition of 802.1p- support in the destination device

Intrusion Prevention

Monitoring and blocking of login attempts and port scans

IP spoofing

Source IP address check on all interfaces: only IP addresses belonging to the defined IP networks are allowed

Access control lists

Filtering of IP or MAC addresses and preset protocols for configuration access

Denial of Service protection

Protection from fragmentation errors and SYN flooding

General

Detailed settings for handling reassembly, PING, stealth mode and AUTH port