Sanwa Electronic Instrument Co Ltd 92082 User Manual

TR

TR

The RX-482 Super Response SSL receiver features a built-in antenna, so no more unsightly antenna sticking out of your model and no antenna to 

worry about being damaged during use. Just mount the RX-482 Super Response SSL receiver in the upright position in your model and enjoy the 

same solid reception as you've come to expect from other Airtronics and Sanwa receivers. Combined with Airtronics or Sanwa Super Response 

SRG digital servos, the RX-482 Super Response SSL receiver will give you reaction speeds like never experienced before!
When used with an Airtronics M12S, M12, MT-4S or Sanwa EXZES-Z transmitter and a Super Vortex series ESC or other SSL compatible device, the 

SSL function allows you to change many programming mode options directly from the transmitter using the transmitter's CODE AUX function, 

on the fly - even while you're driving. In addition, telemetry data such as speed or RPM, ESC temperature, motor temperature (if supported), and 

battery voltage can be read directly from the Super Vortex series ESC and displayed on the transmitter.

2.4GHz FH4T Super Response SSL Receiver User's Guide

Bind LED Condition Indicator:
The Bind LED on the receiver can be used to determine receiver condition at a glance. The 

Bind LED will alert you to various receiver conditions, as described below:

Built-In Antenna

Blue
Blue Flash Slow/Blue Flash Fast
Red & Blue Flashing
Red

Receiving RF Signal
Binding Operation
Receiver Battery Fail Safe Activates
No RF Signal After Receiver Battery Fail Safe Activates

This receiver is not compatible with Airtronics or Sanwa AM, FM or 2.4GHz FH2 or FH3 surface transmitters, or Airtronics or Sanwa 

aircraft transmitters. It's not compatible with any other transmitter brands. SSL function only available when used with an M12S, M12, MT-4S or 

EXZES-Z transmitter and a Super Vortex series ESC or other SSL compatible device. Super Response (SSR) feature only available when used with 

an Airtronics or Sanwa FH4T transmitter in SSR Channel Response Mode with Airtronics or Sanwa Super Response SRG digital servos. Telemetry 

requires telemetry capable transmitter (M12S, M12, MT-4S, MT-4 or EXZES-Z) and Super Vortex series ESC. If not using a Super Vortex series 

ESC, the RX-482 Super Response SSL receiver can send telemetry data for the voltage of the receiver battery pack only.

The receiver's Nominal Input Voltage is 3.7 to 7.4 volts. A 2 cell LiPo or LiFe battery pack can be used to power the receiver without 

the use of a voltage regulator. This allows you to take advantage of the higher torque and higher speed provided by using high-voltage 7.4 volt 

servos. Only use a 2 cell LiPo or LiFe battery pack if your servos are rated to handle the higher voltage!

P/N 92082

Bind Button

Bind LED

Antenna

= Signal
= Positive
= Negative

CH 1 - Steering

CH 2 - ESC/Throttle

CH 3 - Auxiliary 1

CH 4 - Auxiliary 2

BATT/SSL

* If using a Super Vortex series ESC, plug the ESC 

into  the  BATT/SSL  slot,  otherwise  SSL  features 

and telemetry data will not be available. All other 

types of ESC's should be plugged into the CH 2 - 

ESC/Throttle slot.

• Although the reception capability of this receiver is equal to our other receivers that feature an external antenna, because the internal antenna 

is positioned lower in your model, the reception distance will be shorter in actual use.

• Do to the internal antenna position, this receiver is not suitable for use in an R/C boat. It should be used in R/C cars and trucks only.
• Analog servos are not compatible with SHR or SSR Channel Response Modes. If using analog servos, you must use the NOR Channel 

Response Mode. Analog servos and/or the receiver can be damaged if you use them with SHR or SSR Channel Response Modes.

• Any brand and type of digital servo can be used with the SHR Channel Response Mode, however, only Airtronics or Sanwa Super Response SRG 

digital servos can be used with the SSR Channel Response Mode. If your ESC does not operate correctly with the Throttle Channel Response 

Mode set to SHR or SSR, change the Throttle Channel Response Mode to NOR (Normal).

• The receiver is susceptible to vibration, shock and moisture. Take appropriate measures to protect against vibration and moisture. It's okay to 

wrap the receiver in protective foam rubber if desired. Doing so will not affect the reception distance.

• There is a danger of runaway operation if connectors loosen during use. Make sure that all connectors are securely fitted.
• The receiver operates on the 2.4GHz frequency band. The 2.4GHz connection is determined by the transmitter and receiver pair. Unlike 

ordinary crystal-based systems, your model can be used without frequency control.

• The 2.4GHz frequency band may be used by other devices, or other devices in the immediate area may cause interference on the same 

frequency band. Always before use, conduct a bench test to ensure that the servos operate properly. Also, conduct checks with the transmitter 

as distant as possible from your model to ensure adequate reception distance.

• The response speed of the receiver can be affected if used where multiple 2.4GHz transmitters are being used, therefore, carefully check the 

area before use. Also, if response seems slow during use, stop your model immediately and discontinue use.

• If the 2.4GHz frequency band is saturated (too many transmitters on at once), as a safety precaution, the transmitter and receiver may not 

pair when turned on. Once the frequencies have been cleared, or the saturation level has dropped, your transmitter and receiver should pair 

when turned on without any problems.

• For the best reception distance possible, the top of the receiver MUST be toward the top of your model 

(as shown in the illustration) and the receiver should be mounted as high as possible in your model.

• The receiver can be mounted inside a receiver box, however, when mounting inside a receiver box, the 

antenna position will be lower and the reception distance may be shorter.

• The receiver should be mounted securely to your model using a piece of double-sided foam tape to help 

minimize vibration. It's okay to wrap the receiver in protective foam rubber, if desired. Doing so will not 

affect the reception distance.

• Frequency .................................................................................2.4GHz FH4T Selectable Via Transmitter
• Nominal Input Voltage ...............................................................................................................3.7 to 7.4 Volts
• Weight ...................................................................................................................................................0.25oz (7.1g)
• Dimensions ............................................................................0.71 x 0.96 x 1.06in (18.2 x 24.4 x 27.1mm)
• Battery Fail Safe Limit ................................................................................................3.5 to 7.4 Volts (FH4T)