BRK Brands Inc FAL-WAT User Manual
INTRODUCTION
Congratulations on your purchase of the ONELINK Wireless
Water Sensor. Your Water Sensor can monitor the presence
of water in areas such as a sump pump, basement/cellar,
beach house, under sinks, and water pipes. This Quick Start
Guide describes how to set up and troubleshoot your Water
Sensor. For a full system set-up manual, please visit our
website: www.onelinkhome.com
Congratulations on your purchase of the ONELINK Wireless
Water Sensor. Your Water Sensor can monitor the presence
of water in areas such as a sump pump, basement/cellar,
beach house, under sinks, and water pipes. This Quick Start
Guide describes how to set up and troubleshoot your Water
Sensor. For a full system set-up manual, please visit our
website: www.onelinkhome.com
CONTROLLING YOUR SENSOR
Using your computer and the Wireless System Gateway, you
locally manage your home environment with the ONELINK
Wireless software. When configured, the system can notify
you of any new events by sending an e-mail when your Water Sensor detects
an event. An event is defined as a change from a wet or dry state where the
tip of the water sensor probe is located.
Using your computer and the Wireless System Gateway, you
locally manage your home environment with the ONELINK
Wireless software. When configured, the system can notify
you of any new events by sending an e-mail when your Water Sensor detects
an event. An event is defined as a change from a wet or dry state where the
tip of the water sensor probe is located.
How It Works
The Water Sensor detects the presence or
absence of water and notifies you when a water
leak or water deficit is detected. When triggered,
it sends a notification to your Wireless Gateway.
The probe is immersible enabling you to monitor
various types of environments.
The Wireless System Gateway must be installed
before installing your Water Sensor. Consult the
ONELINK System Setup manual for details.
The Water Sensor detects the presence or
absence of water and notifies you when a water
leak or water deficit is detected. When triggered,
it sends a notification to your Wireless Gateway.
The probe is immersible enabling you to monitor
various types of environments.
The Wireless System Gateway must be installed
before installing your Water Sensor. Consult the
ONELINK System Setup manual for details.
INSTALLATION OVERVIEW
Your package contains the following:
Your package contains the following:
Installing your sensor is a simple process.
1. Locate the antenna and screw it into the top-left corner of the sensor until
it is secure. Sharp objects should be stored out of reach of children to
prevent injury.
prevent injury.
2. Insert the batteries. On the top of the sensor, slide open the door and
insert two AAA alkaline batteries. The inside of the sensor indicates the
polarity (+ and -) of the batteries. Close the door after inserting batteries.
The sensor does not support rechargeable NiCad or NiMH batteries.
However, the sensor does employ built-in power saving functionality.
polarity (+ and -) of the batteries. Close the door after inserting batteries.
The sensor does not support rechargeable NiCad or NiMH batteries.
However, the sensor does employ built-in power saving functionality.
3. Mount the sensor.
Installing Your Wireless Water Sensor
Your sensor can either be mounted on a wall or just sit on a horizontal surface.
Your sensor can either be mounted on a wall or just sit on a horizontal surface.
Wall Mount Your Wireless Water Sensor
Warning: When mounting near a window, drilling too close to the glass
could break the glass and possibly cause it to shatter. The window
extends deeper into the frame than can be seen; therefore, ensure
your screw is beyond the glass before drilling. Thoroughly clean and
dry the surface.
1. Mount the sensor securely using the screws in the
Warning: When mounting near a window, drilling too close to the glass
could break the glass and possibly cause it to shatter. The window
extends deeper into the frame than can be seen; therefore, ensure
your screw is beyond the glass before drilling. Thoroughly clean and
dry the surface.
1. Mount the sensor securely using the screws in the
hardware kit. Using the holes on the drilling template
found later in this guide, mark the position of the
holes to be drilled. For drywall or other composite
surfaces use a 7/32” drill bit. Drill a hole for each of
the mounting screws and insert a plastic wall anchor
into each hole. For other solid surfaces, use a 1/16” drill bit.
Drill a pilot hole for each of the mounting screws.
found later in this guide, mark the position of the
holes to be drilled. For drywall or other composite
surfaces use a 7/32” drill bit. Drill a hole for each of
the mounting screws and insert a plastic wall anchor
into each hole. For other solid surfaces, use a 1/16” drill bit.
Drill a pilot hole for each of the mounting screws.
2. Ensure that fresh batteries have been installed.
3. Mount the sensor onto the screws and slide down to lock into place.
3. Mount the sensor onto the screws and slide down to lock into place.
Attaching the Water Probe
The probe, which attaches to the Water Sensor, is immersible and designed
to monitor the presence of water.
1. Insert the plug into the bottom of the sensor.
2. Place the Water Probe in the location you
The probe, which attaches to the Water Sensor, is immersible and designed
to monitor the presence of water.
1. Insert the plug into the bottom of the sensor.
2. Place the Water Probe in the location you
wish to monitor.
Wall Mount Drilling Template
Mounting tools: Screwdriver, electric drill or awl. On hard surfaces, it is
recommended that you pre-drill 1/2-inch deep pilot holes with a drill bit
slightly smaller than the bracket mounting screws before securing the bracket
to the surface. When mounting a sensor on soft surfaces like sheetrock, use
an awl to punch holes in the material slightly smaller than the plastic anchors
included in the hardware mounting kit.
Mounting tools: Screwdriver, electric drill or awl. On hard surfaces, it is
recommended that you pre-drill 1/2-inch deep pilot holes with a drill bit
slightly smaller than the bracket mounting screws before securing the bracket
to the surface. When mounting a sensor on soft surfaces like sheetrock, use
an awl to punch holes in the material slightly smaller than the plastic anchors
included in the hardware mounting kit.
The illustration is drawn to a one-to-one scale, which means that
it provides the exact dimensions required to mount the unit.
Feature Locator
1.6 mm (1/16 inch)
maximum
maximum
Top
Drill holes in
these positions
these positions
2
.0
i
n
1
QUICK START GUIDE
Water Sensor
M08-0238-002 07/12
A
AA
A
AA
Wireless
Water
Sensor
Antenna
External Water
Probe
Hardware
Mounting Kit
Batteries
Installation Hints
Please consider the following points when mounting the sensor:
•
Please consider the following points when mounting the sensor:
•
The ONELINK Wireless Water Sensor is for indoor use only.
•
Typically, the sensor’s range is 65-200 feet from the Wireless Gateway,
depending on the number of obstacles. These can include metal
framing, thick walls, and other wireless devices operating at 915 MHz.
It is recommended that different positions be tried for optimal results.
depending on the number of obstacles. These can include metal
framing, thick walls, and other wireless devices operating at 915 MHz.
It is recommended that different positions be tried for optimal results.
Features and Specifications
•
•
Operates on 2-AAA Alkaline batteries
•
LED indicator when sensor is triggered
Frequency range: 915 MHz
Typical open air range (line of sight): 200 ft (60 m)
Typical Range Indoors: 65 feet (20 m)
Sensor size: 1.613” x .615” x 3.441” (not including probe)
Operational temperature:
14˚ to 131˚ F with all components operating
within manufacturer thermal limits
within manufacturer thermal limits
Battery compartment