Draper 227016 Leaflet
Installation Instructions
227016 T-Bar Twist Clips by Draper
Copyright ©2008 Draper Inc. Form 227016_T-BarTwistClips_Inst08 Printed in U.S.A.
➀ Loosen the clip assembly by turn ing the formed steel hanger
counterclockwise.
➁ Spread the clip assembly apart, place over the T-irons, and fi rmly
squeeze the clip assembly back to geth er, mak ing sure the clip is fi rmly
seated around the T-iron. Retighten by using pliers to turn the formed steel
hanger clockwise. Make sure it is fully tightened.
➂ Se cure with the nut. Tighten with pliers.
counterclockwise.
➁ Spread the clip assembly apart, place over the T-irons, and fi rmly
squeeze the clip assembly back to geth er, mak ing sure the clip is fi rmly
seated around the T-iron. Retighten by using pliers to turn the formed steel
hanger clockwise. Make sure it is fully tightened.
➂ Se cure with the nut. Tighten with pliers.
Please Note: Make sure the clip is fully tightened around
the T-iron, and that the formed steel hanger and the nut are
fully tightened. Poorly tightened clip assemblies, hangers
or lock nuts allow the T-Bar Twist Clip to work loose.
the T-iron, and that the formed steel hanger and the nut are
fully tightened. Poorly tightened clip assemblies, hangers
or lock nuts allow the T-Bar Twist Clip to work loose.
➃ Test by trying to pull the twist clip open and by pulling down on the hanger.
The clip should not pull open.
➄ Suspend “S” hooks (not included) from the holes in the clips and hook
through holes in the front of the screen mounting brack et. For added safe ty,
crimp both ends of the “S” hooks so the screen can not come off.
Please Note: T–Bar Twist Clips are not rec om mend ed for screens larg er
than 70" x 70" unless T-irons are reinforced.
The clip should not pull open.
➄ Suspend “S” hooks (not included) from the holes in the clips and hook
through holes in the front of the screen mounting brack et. For added safe ty,
crimp both ends of the “S” hooks so the screen can not come off.
Please Note: T–Bar Twist Clips are not rec om mend ed for screens larg er
than 70" x 70" unless T-irons are reinforced.
If you encounter any diffi culties installing T-Bar Twist Clips, call your dealer
or Draper, Inc., Spiceland, Ind., (765) 987-7999; fax (765) 987-7142.
or Draper, Inc., Spiceland, Ind., (765) 987-7999; fax (765) 987-7142.
Caution
➀ Read and understand these instructions; keep them for future
reference. Follow instructions carefully.
➁ 227016 T-Bar Twist Clips are for use with Star or Luma projection
screens through 70" wide; for V Screens, use part number 227004.
➂ Locate the screen where the audience can best see it, and where other
room
reference. Follow instructions carefully.
➁ 227016 T-Bar Twist Clips are for use with Star or Luma projection
screens through 70" wide; for V Screens, use part number 227004.
➂ Locate the screen where the audience can best see it, and where other
room
fur
nish ings permit.
➃ Mount the screen so that the bottom of the picture, when screen is fully
extended, will be above the heads of viewers.
➄ Screen should be installed level (using a carpenter’s level).
extended, will be above the heads of viewers.
➄ Screen should be installed level (using a carpenter’s level).
➅ Nothing should be fastened to screen dowel or viewing surface.
NOTE: Make sure Twist Clips are properly tightened.
NOTE: Make sure Twist Clips are properly tightened.
®
T-Bar Twist Clip with Star
T-Bar Twist Clip with Luma
Clip
Assembly
Assembly
Screen
Hanger
Hanger
Nut
Clip
Assembly
Assembly
Screen
Hanger
Hanger
Nut
crimp
crimp
crimp
crimp