Chamberlain Group Inc The 2392 User Manual
CLICKER
MODEL KLIK1U
Universal Garage Door Opener Remote Control
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there
are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit
anyone to cross path of moving gate or door.
© 2007, Clicker Corporation
114A3485
All Rights Reserved
Read instructions thoroughly BEFORE beginning.
Start with garage door closed. Identify garage door opener type - Smart/Learn button or
DIP Switch. Smart/Learn button or DIP Switches are located on motor unit or external
receiver. Refer to owner’s manual if necessary.
DIP Switch. Smart/Learn button or DIP Switches are located on motor unit or external
receiver. Refer to owner’s manual if necessary.
Proceed with instructions according to your type of garage door opener.
NOTE:
Products other than Chamberlain:
If programming fails reverse dip switches (OFF to ON
and ON to OFF).
Products other than Chamberlain:
If programming fails reverse dip switches (OFF to ON
and ON to OFF).
Chamberlain products:
For Chamberlain remotes DO NOT use the “0” position,
use “+” or “-”. If you already have a 3-button remote, DIP
switch #1 must be set to “-” if the large button is to open
the door. It may be necessary to reprogram original
remote controls.
For Chamberlain remotes DO NOT use the “0” position,
use “+” or “-”. If you already have a 3-button remote, DIP
switch #1 must be set to “-” if the large button is to open
the door. It may be necessary to reprogram original
remote controls.
2
12
11
10
9
8
5
3
7
6
4
1
2
Clicker
Remote
Remote
Existing
Remote
Remote
3
4
Press program button
until LED lights.
until LED lights.
5
Match DIP switches. Turn
extra switches OFF.
extra switches OFF.
OR
DIP SWITCH
SMART/LEARN BUTTON
2
3
1
KG
KG
4
Motor Unit
Select a button to program.
Press button times
ensuring LED stops flashing
after each press. Code
is accepted when
door activates.
Press button times
ensuring LED stops flashing
after each press. Code
is accepted when
door activates.
REMOTE CONTROL BATTERY
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications
of this receiver and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
of this receiver and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Dispose of batteries properly.
Replace battery with 3V2032
coin cell battery only.
Replace battery with 3V2032
coin cell battery only.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
CHART A
# of
Brand
Description
Frequency
times to
press
button
press
button
11
Chamberlain
9 Position
390 MHz
12
Chamberlain
9 Position
Canada
Canada
315 MHz
13
Genie
12 Position
390 MHz
14
Linear Multicode
10 Position
300 MHz
15
Chamberlain
8 Position
390 MHz
16
Stanley/Multicode
10 Position
310 MHz
17
Genie
9 Position
390 MHz
18
Linear
Moore-O-Matic
Moore-O-Matic
8 Position
310 MHz
19
Chamberlain
7 Position
390 MHz
CHART B
# of
Brand
Type/Color of
Frequency
times to
Smart/Learn
press
button
button
1
Linear
Mega-Code
318 MHz
2
Chamberlain
Orange
390 MHz
3
Chamberlain
Purple
315 MHz
4
Chamberlain
Green
390 MHz
5
Genie
Overhead Door
Overhead Door
Intellicode
315 MHz
6
Genie
Overhead Door
Overhead Door
Intellicode
390 MHz
7
Stanley
Secure Code
310 MHz
9
Wayne Dalton
Rolling Code
372.5 MHz
www.clickerproducts.com • 1-800-442-1255
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie
is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear
Corporation. Stanley is a Trademark of The Stanley Works.
Button 1
Button 2
Press program button.
6
7
Programming complete.
Press selected button
to test.
Press selected button
to test.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 100°C (212°F) or
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 100°C (212°F) or
incinerate.
The lithium battery should produce power for up to 5 years.
12
11
10
9
8
5
3
7
6
4
1
2
Press and release the
smart/learn button.
smart/learn button.
5
Select a button to program.
Press button times
ensuring LED stops flashing
after each press. Code is
accepted when one of the
following occurs:
Press button times
ensuring LED stops flashing
after each press. Code is
accepted when one of the
following occurs:
Button 1
Button 2
OR
OR
1
See Chart A to
determine # of times to
press button and write
in blank on step 5.
determine # of times to
press button and write
in blank on step 5.
DIP SWITCH
SMART/LEARN BUTTON
Press program button.
6
7
Programming complete.
Press selected button
to test.
Press selected button
to test.
3
Press program button
until LED lights.
until LED lights.
2
1
See Chart B to
determine # of times to
press button and write
in blank on step 5.
determine # of times to
press button and write
in blank on step 5.