Inovonics Wireless Corporation 3B6ETICR65 User Manual
EchoStream™ Select ES1265
3
3
36
60
0°
° P
Paassssiivvee IIn
nffrraaR
Reed
d M
Mo
ottiio
on
n D
Deetteecctto
orr
Installation and Operation Manual - 04098A
IMPORTANT NOTES
•
Products, unless specifically noted, are intended for indoor use.
•
Manually test all products regularly.
•
These products are designed to be installed and maintained by pro-
fessional security technicians.
fessional security technicians.
OVERVIEW:
The ES1265 is a wireless, ceiling-mounted 4-element passive infrared intrusion
detector providing protection from intruders by pyro-sensor array. Micro-con-
troller PIR signal analysis with special ASIC technology for PIR pulse processing
increases immunity to RFI, vibration, static, lightning, ambient temperature
changes and other common causes of false alarms.
detector providing protection from intruders by pyro-sensor array. Micro-con-
troller PIR signal analysis with special ASIC technology for PIR pulse processing
increases immunity to RFI, vibration, static, lightning, ambient temperature
changes and other common causes of false alarms.
LOCATING THE DETECTOR:
Choose a location most likely to intercept an intruder. Refer to the following recommendations:
•
Temperature changes: Do not install the detector outdoors or in a place exposed to sudden temperature changes, or
near equipment such as air conditioners, ventilators, fans, heaters, etc.
near equipment such as air conditioners, ventilators, fans, heaters, etc.
•
Bright light: Avoid bright light, direct or reflected sunlight, automobile headlights or other light sources.
•
Moving Objects: Objects that may move or vibrate, such as curtains, window blinds or decorative banners can cause
false alarms.
false alarms.
•
Exposure to contaminants: Airborne vapors, mists, steam, or fumes can cause detector malfunction.
•
Curtains, Glass, Screens: Infrared energy cannot pass through opaque objects or through transparent or semi-trans-
parent materials such as glass, paper, or curtains. Barriers of these materials create "blind-spots" in intrusion protec-
tion.
parent materials such as glass, paper, or curtains. Barriers of these materials create "blind-spots" in intrusion protec-
tion.
•
Detection Zones: Refer to zone pattern diagrams to determine optimal mounting locations.
MOUNTING THE DETECTOR:
1.
Remove cover from the detector body by loosening the lock screw about 5mm and turning the cover counterclock-
wise. (See Figure 3.)
wise. (See Figure 3.)
2.
Remove the body from the bracket by turning it counterclockwise.
3.
Mount the bracket to the ceiling. Hold the bracket on the ceiling. Mark and drill 4 holes for installation.
4.
Attach the detector body. Install the battery and place the detector body so that the arrow is aligned with the dot
on the bracket. Turn clockwise until the arrow on the body aligns with the arrow on the bracket. (See Figure 3.)
on the bracket. Turn clockwise until the arrow on the body aligns with the arrow on the bracket. (See Figure 3.)
5.
Set Pulse Sensitivity jumper in desired position. Set Frequency Band Selector. (See Figure 1.)
6.
Register the transmitter as described below.
7.
Attach the cover. Place the four tabs of the cover into the matching notches in the base and turn the cover clock-
wise until it fits tightly.
wise until it fits tightly.
MOUNTING HEIGHT
The ES1265 can be mounted to a maximum height of approximately 18 feet (5.5 meters). At 18', the PIR detection pattern
is about twice the diameter of a 10' (3m) installation. As mounting height increases, distance between detection zones also
increases toward the perimeter, and the effects of factors such as floor surface temperature and intruder direction and
speed are intensified. This can contribute to reducing speed of detection. (See Figures 4-6.) Every installation should
include a Walk Test of detection zones, including intrusion paths crossing the edges of the zones.
is about twice the diameter of a 10' (3m) installation. As mounting height increases, distance between detection zones also
increases toward the perimeter, and the effects of factors such as floor surface temperature and intruder direction and
speed are intensified. This can contribute to reducing speed of detection. (See Figures 4-6.) Every installation should
include a Walk Test of detection zones, including intrusion paths crossing the edges of the zones.
PIR SENSITIVITY
The Pulse Count jumper setting provides control for normal or difficult operating environments. Automatic Pulse Count is
recommended for reliable operation in environments which may be subject to temperature fluctuations that might cause
recommended for reliable operation in environments which may be subject to temperature fluctuations that might cause
false alarms. The Single Pulse Count mode is more sensitive to minor temperature variations, and should be used in sites where variant heat sources will not cause alarms (See
Figure 1.)
Figure 1.)
REGISTERING
Transmitters must be registered with the system receiver in order to be monitored and supervised. Each transmitter has a unique factory-programmed identification number.
Refer to the receiver installation instructions for details on registering a transmitter.
Refer to the receiver installation instructions for details on registering a transmitter.
1.
Remove the ES1265 cover as described in “Mounting the Detector.”
2.
To register a transmitter: when prompted by the receiver to "Reset Transmitter", press the Reset button. (See Figure 1.) Replace the ES1265 cover. Follow instructions
to test the transmitter.
to test the transmitter.
Note: TThe EES1265 rretains p
programming d
data iin n
non-vvolatile m
memory. It does not require re-programming after loss of power. Install a new battery and press the reset button
to re-initialize the transmitter and restore programming.
,
A
Battery
B
Tamper Switch
C
Reset Button
D
PIR Sensitivity
E
Test LED
F
Walk Test button
G
Walk Test Reed Switch
H
Frequency Band Selector
Figure 1
PIR Height
Diameter
8'(2.4m)
31' (9.3m)
10'(3m)
38' (11.7m)
12'(3.6m)
46' (9.34m)
18'(5.5m)
70' (21m)
Figure 5
Figure 4
Figure 6
Figure 2
Figure 3
Approximate Effective Detection Diameter*
* See "Mounting Height"
AU (915-928MHz)
EU (868-869 MHz)
NZ (921-928MHz
US (902-928MHz)
MF4232 compatible (915-928MHz)