Inovonics Wireless Corporation 3B6ETRTA2 User Manual

Installation and Operation Manual - 03962B

EThese products are designed to be installed and maintained by professional

security technicians.

E Products, unless specifically noted, are intended for indoor use. 

E Manually test all products regularly.

E Inovonics Wireless radio link, with selectable frequency bands.

E The ES1223S and ES1223D have water-resistant housings that protect the pendant

when worn in the bathtub, shower, rain, or other environments where the pendant
may be splashed with water or momentarily submerged.  

CHANGING THE  BATTERY
1)

Remove three screws from the back of the housing. 

2)

Make sure that the battery is inserted with the positive (+) terminal facing the indicated side of the holder. 

3)

After battery insertion, wait 30 seconds, then press the Reset Button (LEDs will flash) to reset the transmitter to its most 
recent programming. 

4)

Replace back cover. See Caution below. Make sure that the Reset assembly is intact

5)

Thoroughly test the unit before returning to service.

Caution: Replacing back cover

E Do not over-tighten screws when replacing the back cover. 

E Correct torque is 1.5 inch-pounds. 

E Be careful not to damage the gasket material to preserve water-resistance capability. 

E Tighten screws evenly for good seal. 
Discard old battery in accordance to the local laws and practices.
Inovonics Wireless does not take responsibility for batteries that are not discarded properly.

SELECTING OPERATING FREQUENCY
1)

Determine the correct frequency setting for the area in which the ES1223 will be used. 

2)

Set Frequency Jumper as shown in Figure 4. Press reset button.

REGISTERING TRANSMITTERS
Transmitters must be registered with the system receiver in order to be monitored and supervised. Each trans-
mitter has a unique factory-programmed identification number. Refer to the receiver installation instructions for
details on registering a transmitter.

1) If the ES1223 housing is closed: when prompted by the receiver to "Reset Transmitter", press the
Reset Button (Figure 1).
2) If the ES1223 housing is open: when prompted by the receiver to "Reset Transmitter", press the Reset
button (Figure 3). Replace the ES1223 cover. Follow instructions to test the transmitter.

Note: The ES1223 retains programming data in non-volatile memory. It does not require re-programming after loss of power.
Follow “Changing the Battery” instructions to re-initialise the transmitter and restore programming. 

OPERATION
To activate the ES1223S, press and hold the Activation Button for at least 1 second.  
To activate the ES1223D, press and hold both Activation Buttons for at least 1 second. 

Alarm signals are transmitted multiple times, and are indicated by the blinking Transmit LED. 
Holding the buttons results in continuous transmission. 
When either button is released, the FA223S/D will complete its alarm transmission, then will send an alarm restoral signal
so that receiver devices configured for follower mode will return to their normal state.

1

1

1

1

Wearing the ES1223S or ES1223D: Neck cord, Belt Clip or Wrist band
The ES1223 can be carried in three convenient ways: 

E Around the neck as a pendant (standard).

E On a belt with the beltclip attachment (standard). 

E On the arm with optional wristband accessory (ACC623Sor ACC623L).

1

Dimensions:

5.6  x 4.8 x 1.8 cm (2.2 x 1.9 x 0.72”)

Operating temperature:

0° to 60°C (32° to 140°F)

Transmitter frequency range:

Selectable for USA, Europe, Australia or New Zealand (see Figure 4)

Preprogrammed check-in Interval:

12 minutes (EU, MF); 3 minutes (AU, NZ, US)

Reset Button

Reset Button

© 2003 Inovonics Wireless Corporation

e-mail: sales@inovonics.com  •  www.inovonicswireless.com 

E

Transmit Button

Transmit LED

Transmit LED