Inovonics Wireless Corporation 3B6OT9HPX User Manual
5.3.17 06830A © Inovonics, 2017 - www.inovonics.com
2.8 Mount the EN1252
12. Mount the bracket on the wall with the screws provided so
that the catch is on the bottom.
13. Clip the transmitter onto the bracket. Hook the bottom catch
first, then press the top into place.
3 Specifications
Dimensions: 3.5x1.7x0.9”.
Weight: 1.5 oz.
Typical battery life: 1 – 2 years (This does not include current
drawn by external devices).
Internal battery type: 3.0V lithium battery, Inovonics part number
BAT604.
RF output power: 24 dBm (250 milliwatts) equivalent isotropically
radiated power.
Minimum input hold time: 100 ms
Operating environment: Temperature: -4°F to 140°F using
internal battery (-40°F to 185°F using appropriate external power
source).
Humidity: Up to 90% (non-condensing).
Market: North America, Australia, New Zealand.
EchoStream® frequency: 902-928 MHz, Frequency hopping
spread spectrum.
Regulatory compliance: FCC, Industry Canada, RoHS.
Weight: 1.5 oz.
Typical battery life: 1 – 2 years (This does not include current
drawn by external devices).
Internal battery type: 3.0V lithium battery, Inovonics part number
BAT604.
RF output power: 24 dBm (250 milliwatts) equivalent isotropically
radiated power.
Minimum input hold time: 100 ms
Operating environment: Temperature: -4°F to 140°F using
internal battery (-40°F to 185°F using appropriate external power
source).
Humidity: Up to 90% (non-condensing).
Market: North America, Australia, New Zealand.
EchoStream® frequency: 902-928 MHz, Frequency hopping
spread spectrum.
Regulatory compliance: FCC, Industry Canada, RoHS.
Note: Specifications and data are subject to change without
notice.
notice.
4 Television and Radio Interference
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
5 Compliance Information
This device complies with part 15 of the FCC Rules and Industry
Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the
device.
Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Note: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
party responsible for compliance could void the user's authority
to operate the equipment.
5.1 Compliance Notification
The integrator is responsible to ensure the final configuration is
in compliance with the applicable FCC and IC regulations. This
module is limited to battery powered operation only. Connection
to the AC power lines, either directly or through another device,
requires a separate approval from the modular approval
obtained by Inovonics. The integrator is instructed to verify
compliance with the applicable requirements for modular
transmitters. The integrator is responsible for properly labeling
the product containing the module. Product labels must be
permanently affixed on the exterior of the enclosure containing
the module. Labels must include a statement indicating the
product contains the module and the label must specify the FCC
and IC identification numbers:
Example 1: "Contains RF Module - FCC ID: HCQ3B6OT9HPX /
IC ID: 2309A-0T9HPX"
Example 2: "Contains FCC ID: HCQ3B6OT9HPX / IC ID: 2309A-
0T9HPX"
in compliance with the applicable FCC and IC regulations. This
module is limited to battery powered operation only. Connection
to the AC power lines, either directly or through another device,
requires a separate approval from the modular approval
obtained by Inovonics. The integrator is instructed to verify
compliance with the applicable requirements for modular
transmitters. The integrator is responsible for properly labeling
the product containing the module. Product labels must be
permanently affixed on the exterior of the enclosure containing
the module. Labels must include a statement indicating the
product contains the module and the label must specify the FCC
and IC identification numbers:
Example 1: "Contains RF Module - FCC ID: HCQ3B6OT9HPX /
IC ID: 2309A-0T9HPX"
Example 2: "Contains FCC ID: HCQ3B6OT9HPX / IC ID: 2309A-
0T9HPX"
Caution: To maintain compliance to FCC RF exposure
guidelines, install the module at least 20 centimeters (7.8inches)
from the body of the user or nearby persons. The module may
not be co-located with any other transmitters or antennas except
in accordance with FCC multi-transmitter procedures.
guidelines, install the module at least 20 centimeters (7.8inches)
from the body of the user or nearby persons. The module may
not be co-located with any other transmitters or antennas except
in accordance with FCC multi-transmitter procedures.
6 US Patent Numbers
• 7,154,866.
• 7,554,932.
• 7,746,804.
• Other patents pending.
• 7,554,932.
• 7,746,804.
• Other patents pending.