Garmin International Inc 02324 User Manual
Item
Description
À
Vehicle ISO 10487 standard wiring harness connector
Á
and
Â
Infotainment system connectors
Wire Color
Wire Function
Red
12 Vdc battery (constant)
Yellow
12 Vdc battery (switched)
Black
Ground
Orange
Illumination
Blue
Antenna power
Gray
Speaker, front right +
Gray/black
Speaker, front right -
White
Speaker, front left +
White/black
Speaker, front left -
Purple
Speaker, rear right +
Purple/black
Speaker, rear right -
Green
Speaker, rear left +
Green/black
Speaker, rear left -
Secondary Wiring Harness
The secondary wiring harness contains various audio and video
input and output connections. The harness connects directly to
the stereo without modification. You can use this table to
troubleshoot or to identify the functions of the audio and video
connectors.
Connector Label
Function
Notes
À
RVC
VIDEO
Camera video
input
Used for rear view camera
input only.
Á
VIDEO
OUT
Video output
Provides composite video out
for an external monitor.
Â
N/A
CAN
connector
Connects directly to a CAN
BUS or to a PSM connector
using one of the included
cables.
Ã
SUB L/R
Subwoofer
ouput
Connects to a powered
subwoofer. The white
connector is the left channel,
and the red connector is the
right channel.
Ä
N/A
SiriusXM
®
Connects to a SiriusXM
module and antenna.
Å
AUX IN
L/R
Auxillary
audio input
Connects to a general stereo
audio input. The white
connector is the left channel,
and the red connector is the
right channel.
About the CAN Connection
Two cables are supplied to connect the infotainment system to
the vehicle CAN bus, either through a Parameterizable Special
Module (PSM) or directly to the vehicle CAN bus. When a PSM
is available and has been programmed with software that
supports this infotainment system, the PSM connection is
preferred. If there is no PSM, or if the PSM is not programmed
appropriately, the direct CAN connection should be used.
NOTE: You must use only one of the supplied cables to connect
NOTE: You must use only one of the supplied cables to connect
the infotainment system to the vehicle CAN bus.
Connecting the Infotainment System to a PSM
You can use the included cable to connect the infotainment
system to a PSM on a compatible vehicle.
1
Locate the PSM connector in the vehicle.
The PSM connector is typically located under the front left
The PSM connector is typically located under the front left
seat (the driver's seat in the United States).
2
Route the single connector on the PSM cable
À
to the
secondary wiring harness of the infotainment system, and
route the double connector on the PSM cable
Á
to the PSM.
3
Connect the single connector on the PSM cable to the CAN
connector on the secondary wiring harness of the
infotainment system.
4
Insert the two pin connectors into plug 2 of the PSM
connector according to the diagram and table.
Item
Wire Color
PSM Pin
Â
Brown/red
18
Ã
Brown
15
Connecting the Infotainment System to a CAN Bus
You can use the included cable to connect the infotainment
system directly to a CAN bus distributor on a compatible vehicle.
1
Locate the CAN bus distributor
À
in the vehicle.
The CAN bus distributor is located behind the dashboard on
the left side (the driver's side in the United States).You must
remove the panel on the left side of the dashboard (between
the dashboard and the door frame) to access it.
2
Route the harness connector on the CAN cable
Á
to the
secondary wiring harness of the infotainment system, and
route the other connector on the CAN cable
Â
to the CAN
bus distributor behind the dashboard.
3
Connect the cable to the CAN connector on the secondary
wiring harness of the infotainment system.
2
FUSION A-Class Infotainment System Installation Instructions