KAPSCH TRAFFICCOM CANADA INC. 801154 User Manual
CR2000 Reader Installation Instructions
Document A316000-775
2001 MARK IV INDUSTRIES LTD. Revision B, Issue printed on 12/6/2002 1:46 PM,
filename: E:\Ready_To_Convert\Doc\288040.DOC
CONFIDENTIAL: This document is the confidential property of Mark IV Industries Ltd. and may not be released or copied without written permission.
CR2000 - Reader Kit
CR2000 - Reader Kit Packing List
Part Number Description
801075-001
CR2000 Compact Reader
318993-009
DC Power Pack, 110Vac input, output 5V/3A,
15V/1.5A, -15V/0.3A, Skynet #SNP-PA54
15V/1.5A, -15V/0.3A, Skynet #SNP-PA54
318145-177
CR2000 PC Software on Diskette
801076-001 Antenna
Assembly
CR2000 Reader - Connections
CR2000 - Installation Tools
Your tool kit should include (but is not limited to)…
♦ N-type connector crimp tool
♦ N-type connector crimp tool
♦ screwdrivers: flat blade, Philips blade
♦ SAE Socket set
♦ utility knife, wire cutter, wire stripper
CR2000- Installation Items
The kit of reader components described at left does not
include the following required items…
include the following required items…
1 PC cable, RS232 (DTE-DCE), 12 feet (see Fig 1)
A/R antenna mount hardware: bracket(s), clamp(s), mast, etc.
100 feet (or less A/R) of RG213U cable
2.5 feet of RG58U cable
1 N-male connector for RG213U cable
1 N-female connector for RG213U cable
1 N-male connector for RG58U cable
1 N-female connector for RG58U cable
1 each of fixed attenuators: 1, 2, 3, 4, 5, 6, and 7 dB
A/R heat shrink tubing, electrical tape, cable ties and clamps
A/R antenna mount hardware: bracket(s), clamp(s), mast, etc.
100 feet (or less A/R) of RG213U cable
2.5 feet of RG58U cable
1 N-male connector for RG213U cable
1 N-female connector for RG213U cable
1 N-male connector for RG58U cable
1 N-female connector for RG58U cable
1 each of fixed attenuators: 1, 2, 3, 4, 5, 6, and 7 dB
A/R heat shrink tubing, electrical tape, cable ties and clamps
NOTE:
During system installation, the contractor determines
the fixed RF attenuation level required.
CR2000- Installation Overview
♦ The antenna is installed within the distance/angular limits
of the "pick-up point" as indicated in Table 1 on the back
page
page
♦ The reader, power pack, antenna adapter cable and "total
RF attenuation" components are installed at a location
inside the building (see Figure 1 on the back page) that is
(all of)…
inside the building (see Figure 1 on the back page) that is
(all of)…
within 6 feet of a 110Vac power main drop
within 12 feet (4 meters) of the host computer
within 100 feet of the antenna mounting location
outside the building
♦ All system connections are completed as indicated in the
CR2000 - Installation Steps listed on the back page.
♦ The CR2000 PC application software is transferred from
the diskette to the host computer and is running.
♦ The total RF attenuation value is determined by varying
the configuration of the available fixed attenuators.
NOTE:
Where necessary, Mark IV Industries Ltd. I.V.H.S.
personnel may be required to "fine tune" the system RF
attenuation parameters.
attenuation parameters.
Document Revision Record
Rev Date
ECN
Approved
A 18-Jan-01
Preliminary
power
cable
antenna
adapter
cable
PC
cable
CR2000 reader
antenna
software diskette
power
pack