Acumen Technologies Ltd 504 User Manual
Page 3 of 4
PM
ROOM TEMP
*Child-Proof*
SET TEMP
TIMER
C
F
F
C
PM
ROOM TEMP
*Child-Proof*
SET TEMP
TIMER
C
F
F
C
To unlock Child-Proof, press.
UP DOWN DOWN UP DOWN
Child-Proof off
Child-Proof on
The Child-Proof switch disables the buttons on the front of the Remote. Thermostat and timer functions
continue to operate.
continue to operate.
Child-Proof Feature, See Figure 6
C-P
C-P
C-P
The words "Child-Proof"
appear here when Child-
Proof feature is turned on.
appear here when Child-
Proof feature is turned on.
The words "Child-Proof" will
disappear from the LCD.
disappear from the LCD.
The "Child-Proof " will
disappear from the LCD.
SET PRIVATE CODE.
See Figure 7
Fig 6
ROOM TEMP
SET TEMP
TIMER
C
F
F
C
PM
1. Remove the cover at the back of the Remote Transmitter to expose the CHILD-PROOF switch.
2. Slide the CHILD-PROOF switch to position marked C/P to activate the CHILD-PROOF function "*Child-
2. Slide the CHILD-PROOF switch to position marked C/P to activate the CHILD-PROOF function "*Child-
Proof*" will appear on the LCD.
3. In CHILD-PROOF mode the Remote Transmitter will not operate the Remote Receiver until the "child-Proof"
code is used or the switch is returned to the other position.
4. Press the Up and Down buttons in the following sequence:
Up-Down-Down-Up-Down
within 2 seconds button function will be temporarily restored, "*Child-Proof*" will disappear from the LCD.
5. If no button is pressed within 2 minutes, the Remote Transmitter will return to Child-Proof function and
5. If no button is pressed within 2 minutes, the Remote Transmitter will return to Child-Proof function and
"*Child-Proof*" will reappear on the LCD until the Child-Proof switch is slid back to the other position or the
up-down sequence is repeated.
up-down sequence is repeated.
A privacy code can be set to prevent accidental operation of the fireplace by other nearby transmitters.
1.Remove the cover on the back of the Remote Transmitter to expose the code switches. Slide the code
1.Remove the cover on the back of the Remote Transmitter to expose the code switches. Slide the code
switches to your choice of On or Off positions. Factory setting is all "off".
2. Make sure the slide switch on the Remote Receiver is at Off position.
3. Take the Remote Transmitter close to the fireplace or the Remote Receiver (less than 2-10 feet from the
3. Take the Remote Transmitter close to the fireplace or the Remote Receiver (less than 2-10 feet from the
fireplace or Remote Receiver is recommended.)
4. Slide the slide switch on the Remote Receiver to REMOTE position.
5. Install fresh AAA alkaline batteries into the Remote Transmitter.
6. Press any button on the Remote Transmitter, the Remote Receiver will produce a "beep" sound when it
5. Install fresh AAA alkaline batteries into the Remote Transmitter.
6. Press any button on the Remote Transmitter, the Remote Receiver will produce a "beep" sound when it
receives the code from the Remote Transmitter.
7. If you do not hear a "beep" sound from the Remote Receiver, remove the batteries from the Remote
Transmitter and slide the slide switch on the Remote Receiver to Off position, wait for 1 minute and repeat
steps 3 to 6.
steps 3 to 6.
8. Replace the cover of the Remote Transmitter and the Receiver. The system is now ready to operate.
9. If you desire to operate multiple Remote Receivers with the one Remote Transmitter, continue to hold the
9. If you desire to operate multiple Remote Receivers with the one Remote Transmitter, continue to hold the
button on the Remote Transmitter as you bring the Remote Transmitter within 2-10 feet of each Remote
Receiver then slide the slide switch on the Remote Receivers to REMOTE position. Each will acknowledge
receipt of coding with a beep.
Receiver then slide the slide switch on the Remote Receivers to REMOTE position. Each will acknowledge
receipt of coding with a beep.