Bosch Security Systems Inc. 0117-4 User Manual
Copyright © 1997 - 1998 Detection Systems, Inc.
SE3/SE4 Transmitters User’s Guide PN 36447C
9/98
Introduction
The SE3 and SE4 are personal transmitters designed to
work with the Security Escort System. When initiated, a
signal identifying you and your location is sent to the
security office. The SE3 and SE4 may also be tested
within sight of a Receiver or Siren/Strobe by the user.
work with the Security Escort System. When initiated, a
signal identifying you and your location is sent to the
security office. The SE3 and SE4 may also be tested
within sight of a Receiver or Siren/Strobe by the user.
The SE3 and SE4 are available in two models: User (U)
model and Security (S) model. The User model is the
standard model; the Security model has the same
features as the User model, except that the transmitter will
not make an audible tone when transmitting an alarm.
model and Security (S) model. The User model is the
standard model; the Security model has the same
features as the User model, except that the transmitter will
not make an audible tone when transmitting an alarm.
User’s Guide
for the
SE3/SE4 Security Escort Transmitters
The Security Escort system is NOT a substi-
tute for safe behavior. System users should
not take personal risks under the misconcep-
tion that the system will provide protection
that will compensate for taking such risks.
tute for safe behavior. System users should
not take personal risks under the misconcep-
tion that the system will provide protection
that will compensate for taking such risks.
Figure 2. Siren/Strobe and Receiver
Figure 1.
Transmitting an
Alarm
Transmitting an Alarm
Use your transmitter to transmit an alarm only when you
are in danger, seriously injured, or feel threatened.
are in danger, seriously injured, or feel threatened.
NOTE:
Your personal transmitter is an emergency communica-
tion device and should not be used for routine commu-
nications with security officials.
tion device and should not be used for routine commu-
nications with security officials.
Transmitting an alarm alerts a computer located in the
security office that you require emergency assistance. A
display on the computer screen indicates your identity and
approximate location, and an officer is dispatched to
assist you. In some facilities, flashing strobes and
audible sirens will be activated in the vicinity of your
location.
security office that you require emergency assistance. A
display on the computer screen indicates your identity and
approximate location, and an officer is dispatched to
assist you. In some facilities, flashing strobes and
audible sirens will be activated in the vicinity of your
location.
To transmit an alarm:
•
Hold the transmitter away from
your body.
your body.
•
Press both buttons together and
hold!
hold!
In a vehicle, hold the transmitter
close to a window when transmit-
ting.
close to a window when transmit-
ting.
NOTE:
You do not have to point the
transmitter at a Receiver, nor do you
need to be in sight of a Receiver to
activate an alarm.
transmitter at a Receiver, nor do you
need to be in sight of a Receiver to
activate an alarm.
Testing the Transmitter
Test the transmitter weekly. To verify the transmitter’s
operation:
operation:
1. Stand in sight of a Security Escort Siren/Strobe or a
Security Escort Receiver. Receivers are located inside
buildings usually within sight of an exit door. They are
mounted on walls in light beige, rectangular enclo-
sures bearing the Security Escort logo. Siren/Strobes
are typically mounted on outside building walls and on
light poles.
buildings usually within sight of an exit door. They are
mounted on walls in light beige, rectangular enclo-
sures bearing the Security Escort logo. Siren/Strobes
are typically mounted on outside building walls and on
light poles.
2. Press either button on your Security Escort Transmitter
for about one second until you hear a tone. Release.
Then press the other button for about one second until
you hear a tone. Do not hold both buttons down at the
same time as this will generate an alarm.
Then press the other button for about one second until
you hear a tone. Do not hold both buttons down at the
same time as this will generate an alarm.
3. Look for a flashing strobe on a Siren/Strobe or a
flashing green light on a Receiver. A flashing green
light on a Receiver or a flashing strobe on an Siren/
Strobe confirms that the entire system is working. If
you do not see the flashing light or flashing strobe, the
test was not successful.
light on a Receiver or a flashing strobe on an Siren/
Strobe confirms that the entire system is working. If
you do not see the flashing light or flashing strobe, the
test was not successful.
NOTE:
There might be a brief delay of two or three seconds
before the flashing light appears.
before the flashing light appears.
If there is no response, try the test again. If there is no
response the second time, your transmitter might not be
working. Take the transmitter to the security office.
response the second time, your transmitter might not be
working. Take the transmitter to the security office.
Figure 3. Testing the Transmitter
DO NOT HESITATE TO RETRANSMIT.
The system will update your location
each time you retransmit an alarm.
The system will update your location
each time you retransmit an alarm.
Once initiated, the transmitter will send
a signal every few seconds updating
your location until a test is performed.
a signal every few seconds updating
your location until a test is performed.