First International Computer Inc BTH300 User Manual
Getting Started
Pairing BTH with a Bluetooth
Cellular Phone
Before using BTH300, you must first:
Insert an AAA battery.
Once you have paired your BTH300 with a Bluetooth
cellular phone, you do not need to pair it again until you
want to use it with another device.
want to use it with another device.
Connect the earphone.
Turn on BTH300 by pressing “
Turn on BTH300 by pressing “
POWER” button (
Y
on
page 2). The LCD display shows FIC BTH300… (To
turn off BTH300, press and hold “POWER” button
until the display shows - Bye-Bye -.)
until the display shows - Bye-Bye -.)
To Pair the BTH300 with a Phone for the First Time
1. Press and hold “A-B/REC” + , and at the same time
press “POWER” button. The LCD display will show
BT Pair Mode.
BT Pair Mode.
Pair the BTH300 with a Bluetooth cellular phone.
The microphone is located below “LOCK” button (
X
on page 2), and designed for use above chest level.
Hang BTH300 around your neck using the neck strap.
2. Slide “BT ON” button (
\
on page 2) to the right to
enable BT function on BTH300. Bluetooth symbol
will appear on the upper right corner of the LCD
display.
display.
Locking the Buttons
You can lock the buttons to prevent accidental operation
when carrying the BTH300.
when carrying the BTH300.
3. Enable Bluetooth function on your Bluetooth phone
and add BTH300 to a list of paired devices. (For setup
instructions, please refer to the user manual shipped
instructions, please refer to the user manual shipped
with your Bluetooth phone.)
To Lock the Buttons
Slide “LOCK” button toward “POWER” button to lock all
buttons. The ± symbol will show on your LCD display.
Slide “LOCK” button back to unlock.
Slide “LOCK” button toward “POWER” button to lock all
buttons. The ± symbol will show on your LCD display.
Slide “LOCK” button back to unlock.
4. Default password used during setup is 1234.
5. Pairing should take about 2 minutes. After finishing
pairing, “Save… OK” and “-Bye Bye –“ will appear on
LCD display. Then BTH300 will switch off
automatically.
automatically.
Battery Status
Full.
Partially
empty.
6. Turn BTH300 back on. Follow user manual shipped
with Bluetooth phone to connect to BTH300. “HF
Call Connection” will show on LCD display. Press
Call Connection” will show on LCD display. Press
§
button on the earphone to return to MP3 screen.
Battery is low. Bluetooth function will switch
off automatically.
off automatically.
Battery is nearly empty. MP3 playback can
stop any time. Recommend to replace a new
one.
one.
Your BTH300 is now ready to handle phone calls.
- 4 -
- 5 -
Resetting the BTH300
Handle Phone Calls
BTH300 can be reset to its factory settings. This also
clears current pairing.
Once you have paired the BTH300 with your Bluetooth
mobile phone, you can make and receive calls using the
BTH300 as long as:
BTH300 as long as:
To Reset the BTH300
1. Press “MENU” button (
1. Press “MENU” button (
Z
on page 2) and use or
(
]
on page 2) button to scroll to “CONFIG”.
The Bluetooth operation mode on the phone and your
BTH300 is on.
2. Press “POWER” button to enter “SYSTEM SETTING”.
The phone and the BTH300 are on.
3. Use or button to scroll to “DEFAULT”. Press
“POWER” button to reset.
The phone is connected to BTH300.
The phone and the BTH300 are within range of each
The phone and the BTH300 are within range of each
other (up to 10 m; 30 ft) with no solid objects in
between.
Receiving Phone Calls
1. When you receive a call, press
1. When you receive a call, press
§
button on your
headset cord to accept the call.
2. When you
accept
a call, the BTH300 automatically
pauses the music. “Call Connected” will show on
LCD display.
LCD display.
3. Press
§
button again to end the call. If the BTH300
was playing music, it will resume playing.
Making Phone Calls using Voice Dialing
1. Press
1. Press
§
button on your headset cord.
2. After the beep
tone
, perform voice dialing as usual.
3. Press
§
button again to end the call.
Rejecting a Call
Press
Press
button (] on page 2)on your BTH300 to
reject a call, and BTH300 will resume playing.