VTech Telecommunications Ltd 80-7009-00 User Manual
3
Getting started
If the handset will not be used for a long time, disconnect and remove the
battery to prevent any possible leakage.
battery to prevent any possible leakage.
To purchase replacement battery, visit our website at www.vtechphones.com or
call 1 (800) 595-9511.
call 1 (800) 595-9511.
•
•
1
3
Battery installation
Install the battery as shown below.
If the battery compartment cover is on the handset, press on the triangular
tab and slide the cover to remove.
Plug the battery connector securely into the socket inside the handset
battery compartment, matching the color-coded label.
Place the battery with the label THIS SIDE UP facing up and the wires
inside the battery compartment.
#NKIPVJGEQXGTƀCVCICKPUVVJGDCVVGT[EQORCTVOGPVVJGPUNKFGKVVQYCTFU
the center of the handset until it clicks into place.
Charge the handset by placing it in the telephone base or charger. The
CHARGE light is on when the handset charges.
tab and slide the cover to remove.
Plug the battery connector securely into the socket inside the handset
battery compartment, matching the color-coded label.
Place the battery with the label THIS SIDE UP facing up and the wires
inside the battery compartment.
#NKIPVJGEQXGTƀCVCICKPUVVJGDCVVGT[EQORCTVOGPVVJGPUNKFGKVVQYCTFU
the center of the handset until it clicks into place.
Charge the handset by placing it in the telephone base or charger. The
CHARGE light is on when the handset charges.
1.
2.
3.
4.
5.
2
4
5
CHARGE
light
4
Getting started
Battery charging
Once you have installed the battery, the screen indicates the battery status
(see the table below). If necessary, place the handset inthe telephone
base to charge the battery. For best performance, keep the handset in teh
telephone base when not in use. The battery is fully charged after 16 hours of
continuous charging. See the table on
(see the table below). If necessary, place the handset inthe telephone
base to charge the battery. For best performance, keep the handset in teh
telephone base when not in use. The battery is fully charged after 16 hours of
continuous charging. See the table on
page 77
for battery operating times.
If the screen is blank, you need to charge the handset without interruption for
at least 10 minutes to give the handset enough charge to use the telephone
for a short time. The handset beeps and shows Low battery. If you are on a
call in low battery mode, the handset beeps every minutes.
The following table summarizes the battery charge indicators and actions to
take.
at least 10 minutes to give the handset enough charge to use the telephone
for a short time. The handset beeps and shows Low battery. If you are on a
call in low battery mode, the handset beeps every minutes.
The following table summarizes the battery charge indicators and actions to
take.
Battery indicators
Battery status
Action
The screen is blank.
Battery has no charge
and the handset cannot
be used.
and the handset cannot
be used.
Charge without interruption
until the screen shows Low
battery (at least 10 minutes).
until the screen shows Low
battery (at least 10 minutes).
The screen shows
Place in charger and
Place in charger and
ƀCUJGU
Battery has very little
charge and the handset
cannot be used.
charge and the handset
cannot be used.
Charge without interruption
until the screen shows Low
battery (about four minutes).
until the screen shows Low
battery (about four minutes).
The screen shows
Low battery,
Low battery,
ƀCUJGUCPFVJG
handset beeps.
Battery has enough
charge to be used for a
short time.
charge to be used for a
short time.
Charge without interruption
until the screen shows
HANDSET X (about one hour).
until the screen shows
HANDSET X (about one hour).
The screen shows
HANDSET X.
HANDSET X.
Battery is charged.
To keep the battery charged,
place it in the telephone base
when not in use.
place it in the telephone base
when not in use.