Digital Security Controls Ltd. 09RFK55M User Manual

operated device may be connected between the positive supply voltage

and the ‘P/Z’ terminal (maximum load is 50mA).

Applying Power

Once all wiring is complete, and the equipment is secured to the building

structure with at least two screws apply power to the control panel:

1.  Connect the battery leads to the battery.

2.  Connect the AC transformer. 

For more information on control panel power specifications, see the control

panel Installation Manual.

There are several programming

options available for the keypad.

These are described below. Pro-

gramming the keypad is similar

to programming the rest of the

system. When you are in the key-

pad programming sections, the

keypad will display which

options are turned on along the

top of the display.  To turn an

option on or off, press the num-

ber corresponding to the option

on the number pad. The numbers of the options that are currently turned

ON will be displayed.  For example, if options 1 and 4 are on, the display

will look like diagram shown on the different keypad displays. 

For information on programming the rest of your security system, please

refer to your system’s Installation Manual.

All LCD programming is done per keypad. If more than one LCD keypad is

present on the system, labels programmed at one keypad can be broadcast

to all other LCD keypads. Perform the following procedure in order to broad-

cast labels:

Step 1 - Program one LCD keypad completely.

Step 2 - Make sure all LCD keypads are connected to the Keybus.

Step 3 - Enter keypad programming by pressing [4][8][Installer

Code][4], then enter section [998] at the keypad that was programmed.

The keypad will now broadcast all the information programmed to all the

other LCD keypads on the system.

Step 4 - When the keypad is finished press the [#] key to exit.

Hold (<>) keys for 2 seconds to enter language programming, scroll to

the desired language and Press [4] to select.

The keypad will need to be assigned to a partition and slot if supervision or

keypad zones are being used.  Keypad assignments and keypad option pro-

gramming must be done at each keypad individually.

The 1st digit of keypad assignment is used to determine partition assign-

ment (1 to 8).  If partitioning is not used, enter [1].  For Global Keypads,

enter [0].

The 2nd digit of keypad assignment is used to determine slot assignment

for keypad supervision.  Each keypad will be assigned a different slot num-

ber from 1 to 8.  RFK5501/5500 LCD keypads come defaulted in slot 8.  If

LCD keypads are used one LCD keypad must remain in slot 8.

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [4][8][Installer’s Code]

2.  Press [000] for Keypad Programming

3.  Press [0] for Partition and Slot Assignment

4.  Enter the 1st digit (0 to 8 for partition assignment)

5.  Enter the 2nd digit (1 to 8 for slot assignment supervision)

6. Press the [#] key twice to exit programming.

7. After assigning all keypads, perform a supervisory reset by entering

[4][8][Installer’s Code][902] and wait for 60 seconds.

8. Press the [#] key to exit programming after 60 seconds.

1. Enter keypad programming by pressing [4][8][Installer Code][4]. Enter

the 3-digit section number for the label to be programmed.

2. Use the arrow keys (<>) to move the underline bar underneath the let-

ter to be changed. 

3.

Press the number keys [1] to [9] corresponding to the letter you require.

The first time you press the number the first letter will appear. Pressing the

number key again will display the next letter

.

4. When the required letter or number is displayed use the arrow keys

(<>) to scroll to the next letter.

5. When you are finished programming the Zone Label, press the [4] key,

scroll to “Save,” then press [4].

6. Continue from Step 2 until all Labels are programmed.

ASCII Characters

Changing Brightness/Contrast

LCD Keypads

1. Press [4][6][Master code].

2. Use the [<][>] keys to scroll to either Brightness Control or Contrast Control.

3. Press [4] to select the setting you want to adjust.

4. a) ‘Brightness Control’: There are multiple backlighting levels. Use the [<][>]

keys to scroll to the desired level.

b) ‘Contrast Control’: There are 10 different display contrast levels. Use the

[<][>] keys to scroll to the desired contrast level.

5. To exit, press [#].

LED/ICON Keypads

1. Press [4][6][Master Code].

2. Use the [>] key to move through the 4 different backlighting levels.

3. The level is automatically saved when you press [#] to exit.

Changing the Buzzer Level

LCD Keypads

1. Press [4][6][Master Code].

2. Use the [<][>] keys to scroll to Buzzer Control.

3. There are 21 different levels, use the [<][>] keys to scroll to the desired level.

4. To exit, press [#].

LED/ICON Keypads

1. Press [4][6][Master Code].

2. Use the [<] key to move through the 21 different buzzer levels.

3. The level is automatically saved when you press [#] to exit.

All door chime programming is done per keypad. If more than one keypad is

present on the system, door chime programmed at one keypad can be broad-

cast to all other keypads. Perform the following procedure in order to broadcast

door chime:

Step 1 - Program one keypad completely.

Step 2 - Make sure all keypads are connected to the Keybus.

Step 3 - Enter keypad programming by pressing [4][8][Installer Code][4], then

enter section [994] at the keypad that was programmed. The keypad will

now broadcast all the door chime information programmed to all the

other  keypads on the system.

Step 4 - When the keypad is finished press the [#] key to exit.

4

1

Toggle Option

1 _  _  4  _  _  _  _

[1] - A, B, C, 1 [4] - J, K, L, 4 [7] - S, T, U, 7 [0] - Space

[2] - D, E, F, 2 [5] - M, N, O, 5 [8] - V, W, X, 8

[3] - G, H, I, 3 [6] - P, Q, R, 6 [9] - Y, Z, 9,0