Digital Security Controls Ltd. 12GS3125 User Manual
GS3125/GS3105
67
G
G
G
G
G
Options
This page is used to set the options relating to the board.
Dial options
This part is used to enter some of the characteristics relating to the telephone numbers used.
Prefix: This Device will prefix the digits entered in this field to all the telephone numbers dialled through the GSM Interface
Prefix: This Device will prefix the digits entered in this field to all the telephone numbers dialled through the GSM Interface
function. If necessary enter a Prefix (maximum 8 digits) in this field. If no Prefix is required, leave this field empty.
Digits to Remove: If this Communicator is connected downstream to a switchboard, the telephone numbers (programmed
on the Control panel) must be preceded by the switchboard number (normally one digit). As the switchboard number is
not required when calls are sent over the GSM Network, it must be removed from the digits which form the telephone
number. Enter the number of digits that form the switchboard number (e.g. if switchboard number is 01, enter 2 in the
“Digits to remove” field, as 2 numbers form the switchboard number).
not required when calls are sent over the GSM Network, it must be removed from the digits which form the telephone
number. Enter the number of digits that form the switchboard number (e.g. if switchboard number is 01, enter 2 in the
“Digits to remove” field, as 2 numbers form the switchboard number).
The telephone number should at least have two digits more that the number in the “Digits to remove” area,
otherwise the engaged tone will be come through, e.g.:
— the dialled telephone number is 0123, with 2 digits to be removed = correct, the remaining number to be inserted is 23.
— the dialled telephone number is 123, with 2 digits to be removed = engaged tone, the remaining number
to be inserted is 3.
otherwise the engaged tone will be come through, e.g.:
— the dialled telephone number is 0123, with 2 digits to be removed = correct, the remaining number to be inserted is 23.
— the dialled telephone number is 123, with 2 digits to be removed = engaged tone, the remaining number
to be inserted is 3.
Enable Black List: Check this box if you do not wish to receive calls from telephone numbers, authorising only the
numbers selected previously using the White List function (Phonebook page->White List).
Only the “Black List” option cancels the call immediately.
When the “Black List” and “Activates Output” options are enabled, there is a delay (some seconds) before
the call is cancelled;
When the Ring is selected for the Activation Confirmation option, there is a delay (some seconds) before the
call is cancelled;
If the output cannot be activated, GS3125/GS3105 cancels the call immediately.
the call is cancelled;
When the Ring is selected for the Activation Confirmation option, there is a delay (some seconds) before the
call is cancelled;
If the output cannot be activated, GS3125/GS3105 cancels the call immediately.
Event priority (GS3125 series only)
This page may be used to program several Communicator priorities, for the transmission of alarm events (see Priority
management section).
Off-Hook: This box can be used to establish the priority of telephone devices connected to the LI terminals (such as a
management section).
Off-Hook: This box can be used to establish the priority of telephone devices connected to the LI terminals (such as a
burglar alarm control panel). It is enabled
by default; to disable it remove the tick
.
Voice Dialer: This box can be used to establish Voice dialer (voice message) priority. It is disabled
by default; to
enable it, mark it with a tick
.
Codes (GS3125 series only)
User Code: Enter the account code in this box (maximum 4 numeric characters) to activate outputs remotely. For further
information, please refer to the section “Activating the Outputs->Remote Activation and Deactivation of the
Outputs”: The default code is set to ‘0001’.
Outputs”: The default code is set to ‘0001’.
Installer Code: The Installer code can be entered in this field (maximum 4 numerical characters). This code allows
access to the “Remote programming” interface when required. The default code is set to ‘0002’.
Generic
This section may be used to set the audio levels of the loudspeaker and microphone fitted to the GSM transmitter.
Speaker volume: The volume of the loudspeaker may be adjusted by shifting the cursor.
Microphone volume: The volume of the microphone may be adjusted by shifting the cursor.
Speaker volume: The volume of the loudspeaker may be adjusted by shifting the cursor.
Microphone volume: The volume of the microphone may be adjusted by shifting the cursor.
WARNING: if the volume on the microphone is too high, it may corrupt the DTMF tones from devices
connected to the LI terminals, making them unrecognizable.
connected to the LI terminals, making them unrecognizable.
Tones...: Select the name of Communicator’s country of installation: the selected country will establish a series of
parameters for the proper working of the simulated telephone call.
LE failure timeout : Enter the time in seconds (between 10 and 3600 seconds) for the Line down on the LE terminals,
before the PSTN Fault event occurs.
The time may increase up to 60 seconds if some telephone devices are connected to the terminals LI.
LE restore timeout: enter the time in seconds (from 30 to 3600) that the telephone line must be connected to the LE
terminals before the PSTN Fault event is reset.