Digital Security Controls Ltd. 163G4005 User Manual
10
Universal Cellular Communicator
GS4005, 3G4005/AM and 3G4005/EU mounting
1. Mark the position of the holes [8] required to fix the plastic base [2] and the antitamper device [13] to the wall.
2. Drill holes in the wall as marked.
2. Drill holes in the wall as marked.
!
Make sure you do not damage wiring or pipes in the chase.
3. Insert the 5 supports into the holes on the wall.
4. Feed the connection cables through the opening on the base.
5. Fix the plastic base to the wall using wall anchors (not supplied).
6. Insert the silicon carbon pills for antitamper on the dedicated support on the base [12].
7. Insert the back-up battery (accessory item).
8. Place the electronic board on the supports [20] and push it down until it clicks into place.
4. Feed the connection cables through the opening on the base.
5. Fix the plastic base to the wall using wall anchors (not supplied).
6. Insert the silicon carbon pills for antitamper on the dedicated support on the base [12].
7. Insert the back-up battery (accessory item).
8. Place the electronic board on the supports [20] and push it down until it clicks into place.
Read the following steps (9, 10 and 11) if the signal with the integrated antenna is low, to mount the ANT5-02 external optional
antenna, else go to step 12.
antenna, else go to step 12.
9. Connect the antenna cable [23] to the connector on the electronic board and fix other connector of the cable to the communi-
cator backplate with the nut and washer [24] (into dedicated hole).
10. Connect the magnetic antenna cable, using the SMA connector.
11. Position the antenna [28] on the upper edge of the base.
11. Position the antenna [28] on the upper edge of the base.
The antenna will be positioned on the point most suited to receiving the GSM signal.
12. Complete the connections on the terminal boards [19].
The length of the power cables cannot exceed 3 meters.
13. Insert the SIM-CARD face down in the SIM holder [14].
!
The SIM-CARD PIN must be disabled before the card is inserted into the Communicator.
It is recommended that you disable call forwarding on your SIM card.
It is recommended that you disable call forwarding on your SIM card.
14. Make sure that the Line Status (Yellow) and System Fault (Red) LEDs flash when the Communicator is switched on: this
indicates that the Communicator is in its initialization phase.
15. Check signal strength:
make sure that at least the LED remains lit; the LED
lit indicates optimal coverage;
if the LEDs and
are OFF, the signal strength is TOO WEAK; for the signal to be of an acceptable level, at least the
LED must be lit.
16. Close the Communicator cabinet: fasten the upper side of the cover [1] to the backplate [2], using the hinges [9] and then fix
the cover using the screw [7], that you can find on the backplate.
Connect power circuit and the telephone line only after the cabinet has been secured to the wall and has been connected to
the protective earth ground of the building.
Before inserting or removing the SIM card, please ensure the device is powered down.
the protective earth ground of the building.
Before inserting or removing the SIM card, please ensure the device is powered down.
Tamper detection
The activation of tamper switch (optional) allows you to detect the Communicator cover opens or the removal of the device from
the wall (see “Jumpers Description > TMP”).
For the opening of the communicator cover or the removal of the communicator from the wall, will activate the send of an SMS and/
or voice message to one or more phone numbers, or an output will be activated, it is necessary, by the DLS 5 Console, to program
the Communicator (insert phone numbers at the event Tamper / Restore and in the page of Programming from PC-> Inputs /
Outputs enable an Output. After the programming, close the cover and power up the Communicator. After the initialization phase
the wall (see “Jumpers Description > TMP”).
For the opening of the communicator cover or the removal of the communicator from the wall, will activate the send of an SMS and/
or voice message to one or more phone numbers, or an output will be activated, it is necessary, by the DLS 5 Console, to program
the Communicator (insert phone numbers at the event Tamper / Restore and in the page of Programming from PC-> Inputs /
Outputs enable an Output. After the programming, close the cover and power up the Communicator. After the initialization phase