Digital Security Controls Ltd. 17TL280LER User Manual
enabled or disabled. When encryption is enabled, the central station will configure the device to encrypt
communications the next time the communicator module performs a communication to that receiver.
NOTE: Packets will start being encrypted only after the next event is sent to that receiver, or if the unit is
communications the next time the communicator module performs a communication to that receiver.
NOTE: Packets will start being encrypted only after the next event is sent to that receiver, or if the unit is
restarted.
Before leaving the installation site, the communicator TL2803G(R)E Ethernet line shall be
connected via an APPROVED (acceptable to the local authorities) Network Interface Device
(NID). All wiring shall be performed according to the local electrical codes.
connected via an APPROVED (acceptable to the local authorities) Network Interface Device
(NID). All wiring shall be performed according to the local electrical codes.
Communicator Installation Configuration
This HSPA(3G)/dual-path alarm communicator shall be installed by service persons only (service person
is defined as a person having the appropriate technical training and experience necessary to be aware of
hazards to which that person may be exposed to in performing a task and can also take measures to min-
imize the risks to that person or other persons). The Communicator shall be installed and used within an
environment that provides the pollution degree max 2, overvoltages category II, in non- hazardous,
indoor locations only. This manual shall be used with the installation manual of the panel which is con-
nected to the communicator. All instructions specified within the panel manual must be observed.
All the local rules imposed by local electrical codes shall be observed and respected during installation.
is defined as a person having the appropriate technical training and experience necessary to be aware of
hazards to which that person may be exposed to in performing a task and can also take measures to min-
imize the risks to that person or other persons). The Communicator shall be installed and used within an
environment that provides the pollution degree max 2, overvoltages category II, in non- hazardous,
indoor locations only. This manual shall be used with the installation manual of the panel which is con-
nected to the communicator. All instructions specified within the panel manual must be observed.
All the local rules imposed by local electrical codes shall be observed and respected during installation.
Installing the Ethernet Cable (TLXXXX Models Only)
A Category 5 (CAT 5) Ethernet cable must be run from a source with Internet connectivity to the com-
municator module, inside the panel. The communicator end of the cable must be terminated with an
RJ45 plug, which will connect to the communicator’s RJ45 jack after the communicator is installed. All
requirements for installation of CAT5 Ethernet cable must be observed for correct operation of the com-
municator, including, but not limited to, the following:
municator module, inside the panel. The communicator end of the cable must be terminated with an
RJ45 plug, which will connect to the communicator’s RJ45 jack after the communicator is installed. All
requirements for installation of CAT5 Ethernet cable must be observed for correct operation of the com-
municator, including, but not limited to, the following:
l
Do NOT strip off cable sheathing more than required for proper termination.
l
Do NOT kink/knot cable.
l
Do NOT crush cable with cable ties.
l
Do NOT untwist CAT5 pairs more than ½ in. (1.2cm).
l
Do NOT splice cable.
l
Do NOT bend cable at right angles or make any other sharp bends.
NOTE: CAT5 specification requires that any cable bend must have a minimum 2 in. (5 cm) bend radius.
Maximum length of CAT 5 cable is 328 ft. (100 m).
Inserting and Removing the SIM Card
1.
Remove the front cover of the panel to access SIM holder.
2.
Remove power from the panel and disconnect the battery and telephone line.
3.
On the SIM card holder push gently to slide the cover downwards to OPEN. This will unlatch the SIM
card holder on the top edge of the communicator PCB. (See Figure 3).
card holder on the top edge of the communicator PCB. (See Figure 3).
4.
Tilt the top of the SIM card holder downwards to access the SIM card.
NOTE: The SIM can be damaged by bending or scratching contacts. Use caution when handling SIM
cards.
5.
Insert or remove the SIM card, noting the orientation of the notches on the SIM card and the SIM
card holder.
card holder.
6.
When inserting a SIM card, insert the card in the proper orientation and gently push the SIM card
holder down and slide the holder as indicated by the arrow on SIM holder, to LOCK.
holder down and slide the holder as indicated by the arrow on SIM holder, to LOCK.
7.
Reconnect the backup battery and telephone line, apply AC power to panel, and replace the panel
cover.
cover.
Running the RS-232 Cable (R models only)
When installing the communicator for use with 3rd party applications an RS- 232 cable must be con-
nected between the 3rd party device and the communicator module.
NOTE: Maximum cable length for RS-232 cable is 8 ft. (2.4 m).
Please refer to the installation manual for the 3rd party device for wiring instructions.
nected between the 3rd party device and the communicator module.
NOTE: Maximum cable length for RS-232 cable is 8 ft. (2.4 m).
Please refer to the installation manual for the 3rd party device for wiring instructions.
Installing Communicator in Panel
Installing Communicator with HS2016, HS2032, HS2064, and HS2128 Panel
NOTE: Before installing communicator or inserting/removing SIM, ensure that system power is OFF and
telephone line is disconnected.
1.
To assemble supplied mounting bracket, perform the following: (See Figure 1).
a.
Remove the 4 white plastic standoffs from the bag provided with the communicator kit.
b.
Insert the 4 standoffs through the back of the mounting bracket, into the holes at each corner.
(The antenna mounting tab should be facing away from you).
(The antenna mounting tab should be facing away from you).
8