Digital Security Controls Ltd. 18LE9080 User Manual
© 2018 Tyco Security Products. AllRights Reserved.Tech Support:1-800-387-3630 (Canada & U.S.) or 905-760-3000 www.dsc.com
The trademarks, logos,andservice marks displayedon this document are registered in the United States and/or other countries.Any misuse of the trademarks is strictly prohibitedand Tyco willaggressively enforce its intellectualproperty rights to the fullest extent of the law,including pursuit of criminalprosecution wherever necessary.Alltrademarks not ownedby Tyco are the property of their respective owners,andare usedwith
permission or allowedunder applicable laws.Product offerings andspecifications are subject to change without notice.Actualproducts may vary from photos. Not allproducts include allfeatures. Availability varies by region; contact your sales representative
Important: Use this manual in conjunction with the PowerSeries Commercial Reference Manual. Observe all the safety
instructions specified in the manual. Before operation, ensure that the panel is fully assembled and closed.
Safety information: All servicing, except backup battery replacement, must be performed by a service person only. Use
only authorized accessories with this equipment. Observe and respect all rules imposed by local electrical codes. This manual
contains information on limitations regarding product use and function, and on the limitations as to the liability of the
manufacturer. Read the entire manual carefully. For warning information, refer to the PowerSeries Commercial alarm system
Reference Manual. The communicator must be installed by service persons only and used in an environment that provides a
maximum pollution degree of 2 and an overvoltages category II in non-hazardous, indoor locations only. Observe these
instructions and the instructions specified within the panel manual.
Model information: All models are compatible with the control panels HS3032 and HS3128. The communicator
supports Internet Protocol (IP) transmission of panel and communicator events over HSPA/GPRS or LTE. The
communicators are compatible with the following Sur-Gard receivers: SG-System I V1.4+, SG-System II V2.14+, SG-DRL3-IP
V2.36+, SG-DRL4-IP V1.29+ and SG-DRL5-IP V1.05+ (required for visual verification support).
Technical
instructions specified in the manual. Before operation, ensure that the panel is fully assembled and closed.
Safety information: All servicing, except backup battery replacement, must be performed by a service person only. Use
only authorized accessories with this equipment. Observe and respect all rules imposed by local electrical codes. This manual
contains information on limitations regarding product use and function, and on the limitations as to the liability of the
manufacturer. Read the entire manual carefully. For warning information, refer to the PowerSeries Commercial alarm system
Reference Manual. The communicator must be installed by service persons only and used in an environment that provides a
maximum pollution degree of 2 and an overvoltages category II in non-hazardous, indoor locations only. Observe these
instructions and the instructions specified within the panel manual.
Model information: All models are compatible with the control panels HS3032 and HS3128. The communicator
supports Internet Protocol (IP) transmission of panel and communicator events over HSPA/GPRS or LTE. The
communicators are compatible with the following Sur-Gard receivers: SG-System I V1.4+, SG-System II V2.14+, SG-DRL3-IP
V2.36+, SG-DRL4-IP V1.29+ and SG-DRL5-IP V1.05+ (required for visual verification support).
Technical
specifications
The
following technical specifications apply to all models.
Input
voltage: 3.4 - 4.2 V, nominal 3.8 V (provided by the host alarm panels HS3032 and HS3128).
Standby
current: 12 - 28 mA @ 3.8 V.
Alarm
(transmitting) current:750 mA @ 3.8 V (max avg).
Operating
temperature: -10 °C to 55 °C. UL/ULC has only verified operation for range 0-49°C.
Relative
humidity: 5% to 93%, noncondensing.
Mechanical
specifications: 81 x 61 x 11 mm (W x L x H); weight is 25 g.
Model
Market
Operating frequency (MHz)
Typical antenna gain
LE9080 - UL/ULC
listed
listed
Canada, USA
3G - B5: UL: 824 – 849, DL: 869 – 894
B2: UL: 1850 – 1910, DL: 1930 – 1990
4G - B12: UL: 699 – 716, DL: 729 – 746
B13: UL: 777 – 787, DL: 746 – 756
B5: UL: 824 – 849, DL: 869 – 894
B4: UL: 1710 – 1755, DL: 2110 – 2170
B2: UL: 1850 – 1910, DL: 1930 – 1990
B2: UL: 1850 – 1910, DL: 1930 – 1990
4G - B12: UL: 699 – 716, DL: 729 – 746
B13: UL: 777 – 787, DL: 746 – 756
B5: UL: 824 – 849, DL: 869 – 894
B4: UL: 1710 – 1755, DL: 2110 – 2170
B2: UL: 1850 – 1910, DL: 1930 – 1990
1.3 dBi
6.8 dBi
1.2 dBi
2.2 dBi
1.3 dBi
4.6 dBi
6.8 dBi
3G9080 - UL/ULC
listed
listed
Argentina, Canada,
USA
USA
2G - B5: UL: 824 – 849, DL: 869 – 894
B2: UL: 1850 – 1910, DL: 1930 – 1990
3G - B5: UL: 824 – 849, DL: 869 – 894
B2: UL: 1850 – 1910, DL: 1930 – 1990
B2: UL: 1850 – 1910, DL: 1930 – 1990
3G - B5: UL: 824 – 849, DL: 869 – 894
B2: UL: 1850 – 1910, DL: 1930 – 1990
XXXX
3G9080-EU - CE
compliant
compliant
Europe
2G - B8: UL: 880 – 915, DL: 925 – 960
B3: UL: 1710 – 1785, DL: 1805 – 1880
3G - B8: UL: 880 – 915, DL: 925 – 960
B1: UL: 1920 – 1980, DL: 2110 – 2170
B3: UL: 1710 – 1785, DL: 1805 – 1880
3G - B8: UL: 880 – 915, DL: 925 – 960
B1: UL: 1920 – 1980, DL: 2110 – 2170
XXXX
GS9080 -
CE compliant
CE compliant
Europe
2G - B8: UL: 880 – 915, DL: 925 – 960 B3:
UL: 1710 – 1785, DL: 1805 – 1880 B2: UL:
1850 – 1910, DL: 1930 – 1990
UL: 1710 – 1785, DL: 1805 – 1880 B2: UL:
1850 – 1910, DL: 1930 – 1990
XXXX
3H9080 - UL/ULC
listed
listed
Canada, USA
3G - B5: UL: 824 – 849, DL: 869 – 894 B2:
UL: 1850 – 1910, DL: 1930 – 1990
UL: 1850 – 1910, DL: 1930 – 1990
1.3 dBi
6.8 dBi
Inserting and removing the SIM card
Use caution when you handle the SIM card. To avoid damage to the SIM card, ensure that there are no bent or scratched
contacts.
To insert and remove the SIM card, complete the following step:
To insert and remove the SIM card, complete the following step:
l
Insert or remove the SIM card by sliding it in or out of the holder. The notch on the corner of the SIM card must align
with the notch on the base of the holder.
with the notch on the base of the holder.
Installing and replacing the communicator
Note: Before installing the communicator, confirm with the local service provider that there is an available and active
network in the area.
Opening the unit
To open the unit, complete the following step:
Opening the unit
To open the unit, complete the following step:
l
Disconnect power from the panel by removing the power cord and battery.
Installing the communicator
To install the communicator, complete the following steps.
To install the communicator, complete the following steps.
1.
On the new communicator, if required, remove the protective metal tab from the 24-pin CON1 header.
2.
Align the three holes on the communicator module with the plastic pegs on the alarm panel, ensuring the 24-pin
connectors are aligned with matching pins on the panel. See Figure 3.
connectors are aligned with matching pins on the panel. See Figure 3.
3.
Press the module carefully onto the alarm panel.
4.
To attach the antenna place a nylon washer on either side of the hole on the panel and screw the cable into the antenna.
See Figures 4 and 5.
See Figures 4 and 5.
5.
Gently press the main antenna cable connector into the jack labeled JK2 – Main Ant on the PCB. Repeat this step for the
diversity antenna, and connect to the jack labeled JK1 – Div Ant on the PCB.
diversity antenna, and connect to the jack labeled JK1 – Div Ant on the PCB.
6.
Apply power to the panel by plugging in the power supply module.
24-pin CON1
24-pin CON1
header
header
Figure 1: Preparing the panel
Figure 2: Preparing the communicator
Figure 3: Installing the communicator
Figure 4: One antenna installation
Figure 5: Two antenna installation
Replacing the communicator
Note: For panels with a communicator installed, you can use the foam pad in the unit or the foam pad provided in
Note: For panels with a communicator installed, you can use the foam pad in the unit or the foam pad provided in
the standalone cellular communicator kit.
To replace the communicator, complete the following steps.
To replace the communicator, complete the following steps.
1.
Disconnect power from the panel by unplugging the transformer and battery.
2.
Gently remove the main and diversity antenna cables from the PCB.
3.
Release the stand-offs and pull up on the communicator to remove it from the header.
4.
Complete steps 1- 6 in Installing the Communicator.
Communicator configuration
For information on how to configure the communicator, refer to the PowerSeries Commercial alarm system
Reference Manual.
For information on how to configure the communicator, refer to the PowerSeries Commercial alarm system
Reference Manual.
Placement test
To ensure that the communicator is active with a strong signal connection, place the PowerSeries Commercial
panel in its intended location and perform the following steps.
panel in its intended location and perform the following steps.
1.
Ensure the SIM card has been activated.
2.
Using the keypad, enter placement test through installer’s programming: [*][8][Installer Code][850].
3.
View and record the number of bars showing on the LCD keypad.
4.
Compare with the number of bars indicated in the CSQ Levels column shown in the following table.
5.
If 3 or more bars are shown, the location is good and no further action is required.
6.
If 2 or less bars are shown, the location is poor and the communicator may need to be relocated, or an external
antenna extension kit can be used to improve the signal strength.
antenna extension kit can be used to improve the signal strength.
Signal strength
CSQ level
Signal level (dBm)
Installer action
5 bars
14 and higher
-84 and higher
Location is GOOD.
4 bars
11 to 13
-90 to -85
3 bars
7 to 10
-98 to -91
2 bars
5 to 6
-102 to -99
Location is BAD. Not suitable for Cellular operation
1 bar
1 to 4
-108 to -103
No signal
0
-108.8
Check if Cellular coverage is active in your area.
Viewing troubles
For information on how to view troubles, refer to the PowerSeries Commercial alarm system Reference Manual.
Limited warranty
Limited warranty
Digital Security Controls (DSC) warrants that for a period of 12 months from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, DSC shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the
control of Digital Security Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of
abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is
and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the
part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning
this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of
anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product. Warning: Digital Security Controls recommends that the entire system be completely tested
on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it
is possible for this product to fail to perform as expected.
defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, DSC shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the
control of Digital Security Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of
abuse, alteration or improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is
and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the
part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning
this product. In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of
anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product. Warning: Digital Security Controls recommends that the entire system be completely tested
on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it
is possible for this product to fail to perform as expected.
EULA
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is
purchased under the following license terms:
This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired
the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the
manufacturer of the integrated security systems and the developer of the software and any related products or components
(“HARDWARE”) which You acquired.
If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is
NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT
includes computer software, and may include associated media, printed materials, and “online” or electronic documentation.
Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is
licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to
be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If
You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right
to use it.
purchased under the following license terms:
This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired
the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the
manufacturer of the integrated security systems and the developer of the software and any related products or components
(“HARDWARE”) which You acquired.
If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is
NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT
includes computer software, and may include associated media, printed materials, and “online” or electronic documentation.
Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is
licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to
be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If
You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right
to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual
property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual
property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1.
GRANT OF LICENSE This EULA grants You the following rights:
Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT
installed.
installed.
Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used
concurrently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). In
other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will
be used.
concurrently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). In
other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will
be used.
Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license
installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA,
You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA,
You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
2.
DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or
disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law
notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of
an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute
reasonable measures to ensure compliance with the terms and conditions of this EULA.
disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law
notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of
an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute
reasonable measures to ensure compliance with the terms and conditions of this EULA.
Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be
separated for use on more than one HARDWARE unit.
separated for use on more than one HARDWARE unit.
Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is
licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the
HARDWARE as set forth in this EULA.
licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the
HARDWARE as set forth in this EULA.
Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a
server or web site.
server or web site.
Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer
of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts,
the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the
SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.
of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts,
the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the
SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.
Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and
conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its
suppliers.
suppliers.
3.
COPYRIGHT
All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs,
and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE
PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT.
All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are
the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved by
DSC and its suppliers.
EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or
entity subject to Canadian export restrictions.
CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in
accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall
be Toronto, Canada, and the language of the arbitration shall be English.
and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE
PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT.
All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are
the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and
treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved by
DSC and its suppliers.
EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or
entity subject to Canadian export restrictions.
CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in
accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall
be Toronto, Canada, and the language of the arbitration shall be English.
LIMITED WARRANTY
NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE
SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR
ERROR-FREE.
SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR
ERROR-FREE.
CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the
operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-
SOFTWARE or HARDWARE PRODUCTS.
operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-
SOFTWARE or HARDWARE PRODUCTS.
LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY
STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY
UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY
PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY
UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY
PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF
ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON
PURPORTING TO ACT ON ITS BEHALF TO MOD8IFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY
OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON
PURPORTING TO ACT ON ITS BEHALF TO MOD8IFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY
OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY,
BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT
ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF
CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME,
THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.
DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to,
but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as
expected.
FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY,
BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT
ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF
CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME,
THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.
DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to,
but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as
expected.
Regulatory Information
FCC MODIFICATION STATEMENT - Digital Security Controls has not approved any changes or modifications to this
device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Digital Security
Controls n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou
modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.
device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Digital Security
Controls n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou
modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.
FCC AND ISED CANADA INTERFERENCE STATEMENT - This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. This device complies with ISED Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radio électrique subi, même si le brouillage est susceptible d'en comprom-ettre le fonctionnement.
FCC CLASS B DIGITAL DEVICE NOTICE -This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
CAN ICES-3 (B) / NMB-3 (B)
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. This device complies with ISED Canada
licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radio électrique subi, même si le brouillage est susceptible d'en comprom-ettre le fonctionnement.
FCC CLASS B DIGITAL DEVICE NOTICE -This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
CAN ICES-3 (B) / NMB-3 (B)
Model LE9080 FCC ID: F5318LE9080 IC: 160A-LE9080
Model 3G9080 FCC ID: F53173G9080 IC: 160A-3G9080
Model 3H9080 FCC ID: F53183H9080 IC: 160A-3H9080
Model 3G9080 FCC ID: F53173G9080 IC: 160A-3G9080
Model 3H9080 FCC ID: F53183H9080 IC: 160A-3H9080
Note: Only models LE9080, 3G9080 and 3H9080 are UL/ULC listed.
FCC/ISED CANADA WIRELESS NOTICE
This equipment complies with FCC and ISED Canada radiation exposure limits set forth for an uncontrolled environment. The
antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body.
Cet appareil est conforme aux limites d'exposition aux ray-onnements de la ISED Canada pour un environnement non contrôlé.
L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et
votre corps.
Antenna gain must be below. Gain de l'antenne doit être ci-dessous:
antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body.
Cet appareil est conforme aux limites d'exposition aux ray-onnements de la ISED Canada pour un environnement non contrôlé.
L'antenne doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et
votre corps.
Antenna gain must be below. Gain de l'antenne doit être ci-dessous:
Frequency band/Bande de fréquence LE9080 3G9080 LE2077
GSM850/FDD V
xx dBi
xx dBi
xx dBi
PCS1900/FDD ii
xx dBi
xx dBi
xx dBi
LTE B2
xx dBi
xx dBi
xx dBi
LTE B4
xx dBi
xx dBi
xx dBi
LTE B5/B12/B13
xx dBi
xx dBi
xx dBi
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. L'émetteur ne doit pas
être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur.
FCC/IC LABEL:This modular transmitter LE9080, 3G9080 or 3H9080 is labeled with its own FCC ID and IC number. When
the module is installed inside the host device HS3256, HS3128 or HS3032 and the FCC ID/IC of the module is not visible, the host
device shall display the provided label referring to the FCC ID and IC of the enclosed module. This label is shipped together with
the module and it is the responsibility of the integrator to apply it to the exterior of the enclosure as displayed in the following
figure. Le modulaire émetteur LE9080, 3G9080 ou 3H9080 est étiqueté avec son propre ID FCC et le numéro IC. Lorsque le
module est installé à l'intérieur du dispositif hôte HS3256, HS3128 ou HS3032 et la FCC ID / IC du module ne soit pas visible, le
être colocalisé ni fonctionner conjointement avec à autre antenne ou autre émetteur.
FCC/IC LABEL:This modular transmitter LE9080, 3G9080 or 3H9080 is labeled with its own FCC ID and IC number. When
the module is installed inside the host device HS3256, HS3128 or HS3032 and the FCC ID/IC of the module is not visible, the host
device shall display the provided label referring to the FCC ID and IC of the enclosed module. This label is shipped together with
the module and it is the responsibility of the integrator to apply it to the exterior of the enclosure as displayed in the following
figure. Le modulaire émetteur LE9080, 3G9080 ou 3H9080 est étiqueté avec son propre ID FCC et le numéro IC. Lorsque le
module est installé à l'intérieur du dispositif hôte HS3256, HS3128 ou HS3032 et la FCC ID / IC du module ne soit pas visible, le
29010165R001
3G9080/3G9080-EU/3H9080/LE9080 and GS9080 Cellular Alarm
Communicator Installation Instructions
Communicator Installation Instructions