Digital Security Controls Ltd. 18PG9312 User Manual

This feature is dependent on panel software ver-
sion.

Begin the anti-mask calibration process when the
device and magnet are in the final installation pos-
ition. This must be the shortest distance between
the magnet and the device.

For the proper operation of the AM function, align
the magnet with the sensor decorative cover during
calibration. See Figure 5 for parallel and per-
pendicular magnet installation.

Pre-requisites:

To receive an alert for magnet interference, enable
the anti-masking configuration on the device set-
tings menu.

Complete the anti-masking learning process after
enrollment (see Enrolling the PGx312) and with the
device and magnet in the final installation position.

To enable the anti-mask feature, complete the following
steps:

Position the device and magnet pointers to face
each other with reference to Range Coverage Dir-
ections.

Ensure the device and magnet are placed no more
than 5 mm apart on the Z plane. See Range Cover-
age Directions.
Note: During the anti-mask learning process, the
sensor and the magnet must be stable for 10
seconds.

Press and hold the enroll button for 6-8 seconds to
start the anti-mask learning process.

Note: Do not release the enrollment button while
the yellow LED is lit. Release the button after the
green LED lights at 6 seconds and before 8
seconds.
If successful, the green LED flashes three times. If
unsuccessful, the red LED flashes three times.
Note: If the door is open while the enroll button is
pressed, the anti-mask learning process is ignored.

Miscellaneous comments
DSC wireless systems are very reliable and are tested
to high standards. However, due to low transmitting
power and limited range (required by FCC and other
regulatory authorities), there are some limitations to be
considered as follows:
A. Receivers may be blocked by radio signals occur-
ring on or near their operating frequencies, regardless of
the digital code used.
B. A receiver responds only to one transmitted signal at
a time.
C. Wireless devices should be tested regularly to
determine whether there are sources of interference and
to protect against faults.
Specifications
Frequency Band (MHz):Europe and rest of world:
433-434, 868-869. USA: 912-919
Maximum TxPower:
10dBm (10mW) @433MHz
14dBm (25mW) @868MHz
15dBm (30mW) @915MHz
Alarm input:One internal and one auxiliary
Supervision:Signalling at 4-minute intervals
Tamper alert:Report when a tamper event occurs
Communication protocol:PowerG
Power supply: Tyce C
Battery type: 2 x 1.5 VAA Ultimate Lithium Energizer
battery only
Battery life expectancy: 5 years with typical com-
mercial transmissions per day (not tested by UL)
Low battery threshold: 3.0 V
Battery supervision: Automatic transmission of bat-
tery condition data as part of the periodic status report
and immediately upon low battery detection.
Operating Temperature:-40 °C to 66 °C (-40°F to
151 °F)

Note:UL testing temperatures: -35 °C to 66 °C
(-31 °F to 151 °F)
Relative Humidity (RH):Average relative humidity of
approximately 75% non-condensing. For 30 days per
year relative humidity may vary between 85% and 95%
noncondensing.
Note:For UL installations, relative humidity is 93%.
Dimensions (LxWxD): 105 mm x 52 mm x 35 mm
(4.1 in. x 2.0 in. x 1.4 in.)
Device weight (including battery): 154 g (5.4 oz)
Color: Dark grey
UL/ULC notes

The PG9312 has been listed by UL for commercial and residential burglary applic-

ations and by ULC for residential burglary applications in accordance with the

requirements in the StandardsUL 634 and ULC/ORDC634 for Door and Window

Contact. For UL/ULC installations use this device only in conjunction with com-

patible DSC wireless receivers: HSM2HOST9, HS2LCDRF(P)9, HS2ICNRF(P)

9, PG9920, WS900-19, and WS900-29.

Europe: CE/EN (EN50131-2-6 GRADE 2, CLASS IV,

EN50131-6 Type C) listed PG8312: 868 MHz PG4312: 433

MHz.According to EN 50131-1, this equipment can be applied in

installed systems up to and including Security Grade 2, Envir-

onmental Class IV. UK: The PG8312 is suitable for use in sys-

tems installed to conform to PD6662 at Grade 2 and

environmental class IV BS8243.

SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, Tyco Safety Products Canada Ltd declares that the radio equipment type

is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of

conformity is available at the following internet address: www.dsc.com
PG4312: http://dsc.com/pdf/1808001
PG8312: http://dsc.com/pdf/1808002

Frequency Bands

Maximum Power

868.0MHz - 868.6 MHz

14dBm (25mW)

868.7MHz - 869.2MHz

14dBm (25mW)

433.22MHz - 434.64MHz

10dBm (10mW)

European single point of contact: Tyco Safety Products, Voltaweg 20, 6101 XK

Echt, Netherlands.

FCC COMPLIANCE STATEMENT

WARNING!Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to operate the

equipment.
This device has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in residential installations. This

equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful inter-

ference to radio and television reception.
However, there is no guarantee that interference will not occur in a particular install-

ation. If this device does cause such interference, which can be verified by turning

the device off and on, the user is encouraged to eliminate the interference by one

or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one that supplies

power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
FCC ID: F5318PG9312

Innovation Science and Economic Development Canada
(ISED) Statement

This equipment complies with FCC and ISED Canada RF radiation exposure limits

set forth for an uncontrolled environment.
This device complies with FCC Rules Part 15 and with ISED Canada licenceex-

empt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must

accept any interference that may be received or that may cause undesired oper-

ation.
Le present appareil est conforme aux CNR d'ISED Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisee aux deux con-

ditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur

de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouil-

lage est susceptible d'en compromettre le fonctionnement.

W arrant y

(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT

WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWAREWILL

MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE

SOFTWAREWILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible

for problems caused by changes in the operating characteristics of the

HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT

with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF

RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR

CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE

LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT

SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID

BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN

DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW

THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR

INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE

ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER

WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR

LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER

WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO

CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER

WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.

(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO

CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL,

INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON

BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,
STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES

INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE

SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF

CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT,

FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE
CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO

PROPERTY. WARNING:
DSC recommends that the entire system be completely tested on a regular basis.

However, despite frequent testing, and due to, but not limited to, criminal tampering

or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to per-

form as expected. The term IC before the radio certification number signifies that the

Industry Canada technical specifications were met. This Class B digital apparatus

complies with Canadian ICES-003. This device complies with RSS-247 of

Industry Canada. Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any inter-

ference, including interference that may cause undesired operation of the device.

Cet appareil numérique de la classe B est conforme à la norme NMB- 003 du

Canada. Ce dispositif satisfait aux exigences d’Industrie Canada, prescrites dans

le document CNR-247. son utilisation est autorisée seulement aux conditions

suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit

être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est

susceptible de compromettre le fonctionnement du dispositif.

DRAFT SEP 11 (2)