Lotek Wireless Inc SRX600 User Manual
C O D E L O G M O D E
1)Config## > 2)Scan Settings
Guide to the SRX 600 receiver Rev A #10112
Chapter 5 - - Page 48
5
all the different combinations of pulse intervals that can exist, and gives the
receiver information on how to interpret transmitters that transmit sensor data
using that code set.
receiver information on how to interpret transmitters that transmit sensor data
using that code set.
The receiver is configured with the required code set(s) for the study specified at
the time of purchase. Current code sets are Lotek 1, Lotek 2, Lotek 3, Lotek 4 and
Lotek 5. The code set must be selected before data collection can proceed.
the time of purchase. Current code sets are Lotek 1, Lotek 2, Lotek 3, Lotek 4 and
Lotek 5. The code set must be selected before data collection can proceed.
Lotek Code Sets and Firmware
1
(“FIRMWARE”) are protected by copyright
laws and international treaty provisions. LOTEK owns and retains all right,
title and interest in and to the FIRMWARE, including all copyrights, patents,
trade secret rights, trademarks and other intellectual property rights therein.
Licensee’s possession, installation, or use of the FIRMWARE does not
transfer any title to the intellectual property in the FIRMWARE and Licensee
will not acquire any right, title or interest to the FIRMWARE except as
expressly set forth in the Firmware License Agreement included with every
system purchased.
title and interest in and to the FIRMWARE, including all copyrights, patents,
trade secret rights, trademarks and other intellectual property rights therein.
Licensee’s possession, installation, or use of the FIRMWARE does not
transfer any title to the intellectual property in the FIRMWARE and Licensee
will not acquire any right, title or interest to the FIRMWARE except as
expressly set forth in the Firmware License Agreement included with every
system purchased.
1: Lotek Code Sets and Firmware includes, but is not limited by the
following: Lotek-1 (also referred to as Lotek 1993 code set or 1993 code set),
Lotek-2 (also referred to as Lotek 1994 code set or 1994 code set), Lotek-3
(also referred to as Lotek 2000 code set or 2K code set), Lotek-4 (also referred
to as Lotek 2003 code set or 2003 code set) and Lotek-5.
following: Lotek-1 (also referred to as Lotek 1993 code set or 1993 code set),
Lotek-2 (also referred to as Lotek 1994 code set or 1994 code set), Lotek-3
(also referred to as Lotek 2000 code set or 2K code set), Lotek-4 (also referred
to as Lotek 2003 code set or 2003 code set) and Lotek-5.
S
ELECTING
A
C
ODE
S
ET
Codes Sets are accessed via CodeLog > 1)Config## > 2) Scan Settings > 1)Code
Set
Set
. Use the keypad to select the desired code set. If the receiver is Offline then
accessing the codeset feature only provides current setting information. Code sets
can also be selected via Manual > 1)Code Set.
can also be selected via Manual > 1)Code Set.
S
E T T I N G
A
S
C A N
T
I M E
When collecting data the receiver needs to know how long it should scan each
frequency+antenna combination. This is referred to as the scan time. Scan times
are typically set to the maximum transmitter burst interval plus 0.5 seconds.
frequency+antenna combination. This is referred to as the scan time. Scan times
are typically set to the maximum transmitter burst interval plus 0.5 seconds.
Scan time can be set with a resolution of 100ms. The range is 0.1s through 99.9
seconds.
seconds.
Set the scan time via Codelog > 1)Config## > 2)Scan Settings > 2)Param > 2)Scan
Time
Time
. Scan time format is in seconds.