Casablanca Fan Company CASA3TA User Manual
8
Removing
Gently Pull the lower edge
of the control gently out
from the holder.
Gently Pull the lower edge
of the control gently out
from the holder.
Control Storage
Angle control in top first in
the holder until the unit
can be gently pushed back
and snapped onto the
bottom rim.
Angle control in top first in
the holder until the unit
can be gently pushed back
and snapped onto the
bottom rim.
WOOD
SCREW 1”
Note: The wall anchors and
6-32 x 1” screws may be used
in situations where mounting
to a stud is not possible. Use
the inner mounting holes.
After securing the anchor, dis-
card the anchor’s pointed
screws and use the 6-32 de-
cor ovalhead screws supplied.
6-32 x 1” screws may be used
in situations where mounting
to a stud is not possible. Use
the inner mounting holes.
After securing the anchor, dis-
card the anchor’s pointed
screws and use the 6-32 de-
cor ovalhead screws supplied.
VERSA•TOUCH ♦ STORING CONTROL IN HOLDER
DECOR OVALHEAD SCREW
6-32 X 1”
ANCHOR
PANHEAD
SCREW
DRYWALL ANCHOR
TOP GOES
IN FIRST
Wall Installation
Step 1. Locate a
2X4 wall stud in a
convenient loca-
tion.
Step 2. Orient the
control holder as
shown over the
2X4 stud.
Step 3. Use the 1”
wood screws in ei-
ther the inner or
outer mounting
holes.
Install and tight-
en screws by hand
only.
Step 1. Locate a
2X4 wall stud in a
convenient loca-
tion.
Step 2. Orient the
control holder as
shown over the
2X4 stud.
Step 3. Use the 1”
wood screws in ei-
ther the inner or
outer mounting
holes.
Install and tight-
en screws by hand
only.
ROCKER
TYPE
LIGHT
SWITCH
SWITCH
COVER
PLATE
STANDARD
TOGGLE
SWITCH
SWITCH
SWITCH
COVER
PLATE
INNER
MOUNTING
HOLES
CONTROL
HOLDER
OUTER
MOUNTING
HOLES
SCREW
6-32 X 1”
(2)
SCREW
6-32 X
3
/
8
”
(2)
WOOD
SCREW
1”
(2)
DRYWALL
ANCHOR
6-32
(2)
REMOVE TABS
CAUTION! Do not use with wall dimmer.
9V BATTERY
W-42
CONTROL
Rocker Light Switch
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate. Do
not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two outer
mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate. Do
not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two outer
mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATION
W-42
CONTROL
HOLDER
VERSA•TOUCH ♦ INSTALLATION
Standard Light Switch
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up
the two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up
the two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
VERSA•TOUCH ♦ BATTERY INSTALLATION
GUIDE SLOTS
Install Battery
Press battery into
control aligned as
shown. Observe
proper polarity.
Replace the
battery door.
Press battery into
control aligned as
shown. Observe
proper polarity.
Replace the
battery door.
SNAP
SOCKET
PLUG
Remove Battery Door
Turn control on its
front.
Twist a coin to unsnap
the door A. Lift door
away from control B
and remove C.
Turn control on its
front.
Twist a coin to unsnap
the door A. Lift door
away from control B
and remove C.
8
R
Changes or modifications not expressly approved in writing by Casablanca Fan Co. may void
the user’s authority to operate this equipment.
the user’s authority to operate this equipment.