Casablanca Fan Company CASA5T User Manual
1
©2001 Casablanca Fan Co. www.CasablancaFanCo.com
Removing Control
Gently Pull the lower edge
of the control out from the
holder.
Gently Pull the lower edge
of the control out from the
holder.
Note: The wall anchors and
6-32 x 1” screws may be used in
situations where mounting to a
stud is not possible. Use the inner
mounting holes. After securing the
anchor, discard the anchor’s
pointed screws and use the 6-32
decor ovalhead screws supplied.
6-32 x 1” screws may be used in
situations where mounting to a
stud is not possible. Use the inner
mounting holes. After securing the
anchor, discard the anchor’s
pointed screws and use the 6-32
decor ovalhead screws supplied.
VERSA•TOUCH ♦ HOLDER INSTALLATION / STORAGE
DECOR OVALHEAD SCREW
6-32 X 1”
TOP
GOES IN
FIRST
Wall Installation
Step 1. Locate a
2x4 wall stud in a
convenient loca-
tion.
Step 2. Orient the
control holder as
shown over the
2x4 stud.
Step 3. Use the 1"
wood screws in ei-
ther the inner or
outer mounting
holes. Install and
tighten screws by
hand only.
Step 1. Locate a
2x4 wall stud in a
convenient loca-
tion.
Step 2. Orient the
control holder as
shown over the
2x4 stud.
Step 3. Use the 1"
wood screws in ei-
ther the inner or
outer mounting
holes. Install and
tighten screws by
hand only.
ROCKER
TYPE
LIGHT
SWITCH
SWITCH
COVER
PLATE
STANDARD
TOGGLE
SWITCH
SWITCH
SWITCH
COVER
PLATE
INNER
MOUNTING
HOLES
CONTROL
HOLDER
OUTER
MOUNTING
HOLES
SCREW
6-32 X 1”
(2)
SCREW
6-32 X
3
/
8
”
(2)
WOOD
SCREW
1” (2)
1” (2)
DRYWALL
ANCHOR
6-32 (2)
REMOVE TABS
CAUTION! DO NOT USE WITH WALL DIMMER.
9V BATTERY
W-43
CONTROL
Rocker Light Switch
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate.
Do not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two
outer mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
Step 1. Break off the two tabs by pushing outward.
Step 2. Remove the two screws holding the switch cover plate.
Do not remove the cover plate.
Step 3. Orient the control holder as shown and line up the two
outer mounting holes with those on the switch.
Step 4. Install and tighten screws by hand only.
VERSA•TOUCH ♦ CONTROL HOLDER INSTALLATION
W-42
W-43
W-43
CONTROL
HOLDER
VERSA•TOUCH ♦ INSTALLATION
Standard Light Switch
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up the
two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
Step 1. Remove the two screws holding the switch cover
plate. Do not remove the cover plate.
Step 2. Orient the control holder as shown and line up the
two inner mounting holes with those on the switch.
Step 3. Install and tighten screws by hand only.
VERSA•TOUCH ♦ BATTERY INSTALLATION
GUIDE SLOTS
Install Battery
Press battery into
control aligned as
shown. Observe proper
polarity. Replace the
battery door.
Press battery into
control aligned as
shown. Observe proper
polarity. Replace the
battery door.
SNAP
SOCKET
PLUG
Remove Battery Door
Turn control on its front.
Twist a coin to unsnap
the door A. Lift door
away from control B and
remove C.
Turn control on its front.
Twist a coin to unsnap
the door A. Lift door
away from control B and
remove C.
Changes or modifications not expressly ap-
proved in writing by Casablanca Fan Co. may
void the user’s authority to operate this
equipment.
proved in writing by Casablanca Fan Co. may
void the user’s authority to operate this
equipment.
This device complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Control Storage
Angle control in top first
until the unit can be
gently pushed back and
snapped into place.
Angle control in top first
until the unit can be
gently pushed back and
snapped into place.
WOOD
SCREW 1”
ANCHOR
PANHEAD
SCREW
DRYWALL ANCHOR