DONGGUAN ALLLIKE ELECTRONIC CO. LTD BT40 User Manual

1  Press the          (source) button on your speaker, then connect to your 

Bluetooth device. 

2  Begin playback on your Bluetooth device. 
3  Adjust the volume on your speaker by pressing the + or - buttons.

 

Note: Use the controls on your Bluetooth device to control playback.

1  Press the        (phone) button briefly to accept an incoming call. 
  OR
  Press and hold the        (phone) button to reject an incoming call. 
2  Press the        (phone) button during a call to end the call. 

1  Connect an external sound source, such as an MP3 player, by plugging 

a 3.5 mm audio cable (not included) into the AUX IN jack on your 
speaker.

2  Press the          (source) button to enter AUX mode. The LED lights 

green. 

3  Start playback on the external device.
4 Press + and – to adjust the volume.
5  Control playback using the controls on the audio device.

Quick Setup Guide  |  

NS-CSPBTHOL

1  Make sure that your Bluetooth device is turned on and within 33 feet 

(10 meters) of your speaker.

2  On your speaker, press the Source button. Your speaker enters pairing 

mode, and the LED blinks. 

 

Note: Press and hold the Source button to return to pairing mode.

3  Turn on your Bluetooth device and turn on Bluetooth. Set your device 

to pairing mode, then select NS-CSPBTHOL. See the instructions that 
came with your Bluetooth device for information about pairing.

4  If you are asked for a password, enter 0000. When pairing is complete, 

the LED lights solid blue.

5  To disconnect from the paired Bluetooth device, press and hold the 

Source button on your speaker for three seconds. Your speaker 
disconnects from the Bluetooth device and enters pairing mode again.

When your speaker is not paired to a device, the LED blinks blue slowly.

Note: If a device does not automatically reconnect, you may need to reselect 
NS-CSPBTHOL on your Bluetooth device.

Before using your new product, please read 

these instructions to prevent any damage.

1  Connect the small end of your USB charging cable to the micro USB 

port on the back of your speaker.

2  Connect the other end to a USB charging port. The charging 

indicator lights red while charging, then turns off when fully charged.

Note: When the battery is low, you will hear beeps every two minutes. About 
10 minutes later, the speaker will power off automatically.

•  Slide the ON/OFF switch. When on, the LED blinks quickly and the 

speaker enters pairing mode.

• Bluetooth 

speaker 

•  USB charging cable
•  Quick Setup Guide

•  Wirelessly stream from any 

Bluetooth device

•  Rechargeable battery lasts up 

to six hours

•  Speakerphone for hands-free 

talking

Speaker is in pairing mode

Speaker is paired

To audio output such 

as CD/MP3/digital 

music player.

Turn off your speaker.

Move the Bluetooth device out of range.

Turn off your Bluetooth device.

Turn off Bluetooth on your Bluetooth device.

Connect your Bluetooth device to another 
Bluetooth device.

Turn on your speaker. Your speaker searches for the last connected 
Bluetooth device and reconnects.

Make sure that your Bluetooth device is within 33 feet of your speaker.

Turn on your Bluetooth device, then make sure that Bluetooth is on.

Turn on Bluetooth on your Bluetooth device.

Disconnect your Bluetooth device from the other Bluetooth device, then 
set your device to pairing mode. Select NS-CSPBTHOL on your 
Bluetooth device.

Volume down

Phone

Source

Volume up

Micro USB charging port

ON/OFF 
switch

AUX in jack

Charging indicator

Bluetooth LED

NS-CSPBTHOL_15-0783_QSG_V3_EN.ai   1   8/31/2015   7:02:33 AM

NS-CSPBTHOL_15-0783_QSG_V3_EN.ai   1   8/31/2015   7:02:33 AM