Bang & Olufsen BEOCOM2 User Manual

20

21

This equipment complies with Part 68 of the Federal 

Communications Commission (FCC) rules for the 
United States. 

A label is located on the underside of the base unit 

containing either the FCC registration number and 
Ringer Equivalence Number (REN). You must upon 
request, provide the following information to your 
local telephone company: 
  USOC Jack Type: RJ11
  REN: 0.1B

Should you experience trouble with this telephone 

equipment, please contact: 
  Bang & Olufsen America, Inc. 

780 West Dundee Road 

Arlington Heights 

IL  60004 U.S.A. 

  Phone:     (847) 590-4900 
  Main Fax:  (847) 255-7805 

The REN is used to determine the quantity of devices 

which may be connected to the telephone line. 
Excessive RENs on the telephone line may result in the 
devices not ringing in response to an incoming call. In 
most, but not all areas, the sum of RENs should not 
exceed five (5.0). To be certain of the number of 
devices that may be connected to a line, as deter-
mined by the total RENs, contact the local telephone 
company. 

If trouble is experienced with BeoCom 2, for repair or 
warranty information, please contact: 
  Bang & Olufsen America, Inc. 

780 West Dundee Road 

Arlington Heights 

IL  60004  U.S.A. 

  Phone:     (847) 590-4900 
  Main Fax:  (847) 255-7805 

If the equipment is causing harm to the telephone 
network, the telephone company may request that 
you disconnect the equipment until the problem is 
resolved. 

This equipment cannot be used on public coin 

phone service provided by the telephone company. 
Connection to party line service is subject to state 
tariffs. 

Your telephone company may discontinue your 

service if your equipment causes harm to the tele-
phone network. They will notify you in advance of 
disconnection, if possible. During notification, you 
will be informed of your right to file a complaint to 
the FCC. 

Occasionally, your telephone company may make 
changes in its facilities, equipment, operation, or 
procedures that could affect the operation of your 
equipment. If so, you will be given advance notice of 
the change to give you an opportunity to maintain 
uninterrupted service. 

Changes or modifications not expressly approved by 
the party responsible for compliance could void the 
user’s authority to operate the equipment.

This equipment complies with FCC radiation exposure 

limits set forth for an uncontrolled environment. This 
device complies with FCC SAR limit of 1.6mW/g. The 
maximum SAR value measured was 0.26mW/g. This 
device must not be co-located or operating in con-
junction with any other antenna or transmitter.

NOTE: This equipment has been tested and found 
to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against 
harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harm-
ful interference to radio communications. However, 
there is no guarantee that interference will not occur 
in a particular installation.

If this equipment does cause harmful interference 
to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by 
one or more of the following measures:

–  Reorient or relocate the receiving antenna.
–  Increase the separation between the equipment 

and receiver.

–  Connect the equipment into an outlet on a circuit 

different from that to which the receiver is con-
nected.

–  Consult the dealer or an experienced radio/TV 

technician for help. 

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, 
and (2) this device must accept any interference 
received, including interference that may cause un-
desired operation.