Scientific Toys Ltd 4817-24GG User Manual

#99074  SIZE: 210MM X 297MM   PN#65-6297-000-0100

Flathead screwdriver required, not included

1 x 9 Volt Battery

Unscrew

to open

Driving control stick

Forwards

Forwards

Forwards

Driving control stick

Backwards Backwards

Reverse

Left

Right

Driving control stick

Forwards

Driving control stick

Forwards

Backwards

Backwards

Stop

Unscrew to open

BATTERY INSTALLATION
BATTERY REQUIREMENT:
Vehicle: Built-in Rechargeable Battery
Transmitter: 1 x 9V battery (included)

It is recommended that this toy and all accessories be periodically examined for potential hazards 
and that any potentially hazardous parts be repaired or replaced.

VEHICLE
The vehicle is powered by a built-in non-replaceable rechargeable battery. The included rechargeable 
battery is not charged prior to shipment and must be charged before the first use.

Charging The Vehicle
1.   Make sure the vehicle’s switch is in the CHARGE position. (See Diagram 1)
2.   Open the battery cover. (See Diagram 1)
3.  Plug the charging cable USB socket to an USB certified port, 
  i.e., desktop computer / laptop computer / smartphone charger / tablet charger / car changer
4.  Turn the vehicle's switch to "CHARGE" position.
5.  The LED light on car body will flash to show vehicle is charging.
6.  Once the light turned OFF, the vehicle is fully charged. Unplug the USB socket from the USB 
  certified port.
7.  Put back the charging cable into the compartment and replace battery cover. (See Diagram 1)

1.   Unscrew to open the battery lid. Insert a new 1 x 9V battery. (See Diagram 2)
2.   Replace the battery cover.
Note: Remove battery after you have finished using your vehicle.

Caution : Built-In Battery Safety Information 
1.  The vehicle includes a non-replaceable battery. Do not open, disassemble or alter the vehicle in
  anyway.
2.  Adult supervision is required when charging the vehicle.
3.  Charge battery in isolated area. Keep away from flammable materials.
4.  Do not expose to direct sunlight.
5.  Do not recharge the toy if it is hot. Allow it to cool before recharge.
6.  Do not allow the batteries to get wet.
7.  Carefully read the instruction guide and use the batteries correctly.
8.  Rechargeable batteries are only to be charged under adult supervision.
9.  Routine examination for damage to the plug, enclosure and other parts. In the event of any 
  damage, the toy must not be used with USB port until the damage has been repaired.
10. This toy is not intended for children under 3 years old.

Never drive the vehicle on a wet floor, on sand, grass, carpet, in mud, rain or snow. These can cause 
damage to the vehicle. Do not expose the vehicle to extreme temperatures. To protect the vehicle’s 
wheel mechanisms from lint and hair, do not drive it on carpet. Occasionally wipe the vehicle with a 
damp cloth to remove any dirt/dust from wheels. Do not use harsh chemicals to clean the vehicle. 
Modifying or tampering with the vehicle or the transmitter’s internal components can cause a 
malfunction. 

Running the vehicle continuously for long periods of time generates high levels of heat. Heat causes 
wear and tear on the motor. When the vehicle’s battery pack goes flat, let the vehicle cool at least 
10 minutes before installing a newly charged battery pack. This helps keep heat levels down. If the 
vehicle’s motor runs but does not respond to the transmitter, move the transmitter closer to the 
vehicle and try again. If a CB radio is used nearby, it might interfere with the control of the vehicle. 
If this happens, move the vehicle and transmitter away from the CB radio. The vehicle cannot be 
operated near devices with transmitters that use the same frequency. Check the packaging to see 
which frequency your vehicle uses. If the vehicle moves slowly, and a recharged battery pack has 
been installed, check the wheel mechanisms for lint, thread, hair or dust.

START TO PLAY
PAIRING TRANSMITTER WITH VEHICLE
1.  Turn ON the vehicle (See Diagram 1).
2.  Install 1 x 9V battery in the transmitter, the pairing LED light on the transmitter will flash (See 
  Diagram 2).
3.  If pairing success, the pairing LED light will turn OFF
4.  You must pairing the transmitter with the vehicle within 45 seconds, after 45 seconds you must 
  push the control on the transmitter to pair again.
5.  You must  repeat pairing again when the transmitter needs to replace new batteries.

1.  If pairing failed, reinstall the battery of transmitter, move closer and then try again.

2.  If more then one vehicle are pairing at the same time, pair each vehicle one by one.

 

  Vehicle has memory to store the paired data, no need to pair each time play until replace the

  battery in transmitter.

1.  Push both the Driving Control Sticks forwards for forward motion. (See Diagram 3)

2.  Pull both the Driving Control Sticks backwards for reverse motion. (See Diagram 4)

4.  Push only the Left Driving Control Stick forwards to turn Right. (See Diagram 5)

5.  Push only the Right Driving Control Stick forwards to turn Left. (See Diagram 6)

6.  Push the Left Driving Control Stick forwards while pulling the Right Driving Control Stick 

  backwards at the same time. (See Diagram 7)

7.  Push the Right Driving Control Stick forwards while pulling the Left Driving Control Stick 

  backwards at the same time. (See Diagram 8)

8.  Release both Driving Control Sticks, the vehicle will Stop. (See Diagram 9)

9.  Press reverse then Forward quickly to perform Wheelie Action. (See Diagram 10)

Keep packaging as it contains important information.

CAUTION: To prevent battery leakage:

Be sure to insert batteries correctly and always follow the product and battery 

manufacturers' instructions.

Never mix old and new batteries (replace all batteries at the same time).

Never mix Alkaline, standard (Carbon Zinc) or rechargeable (Nickel-Metal Hydride) batteries.

Only batteries of the same or equivalent type as recommended are to be used.

Do not use RECHARGEABLE batteries, unless specified.

Non-rechargeable batteries are not to be recharged.

Rechargeable batteries are to be removed from the product before being charged. 

Rechargeable battery is only to be charged by adults or by children at least 8 years old.

Always remove exhausted or dead batteries from the product.

Remove batteries from product before extended storage.

The supply terminals are not to be short-circuited.

Batteries are to be inserted with correct polarity.

Batteries may explode or leak if misused.

ATTENTION: Battery / Batteries should be installed by an adult only.

ATTENTION: User should remove the battery from the item before disposal.

This appliance is not intended for use by persons (including children) with reduced physical, sensory 

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision 

or instruction concerning use of the appliance by a person responsible for their safety.

• The WEEE symbol if present indicates that this item contains electrical or electronic components 

which must be collected and disposed of separately.

• Never dispose of electrical or electronic waste in general municipal waste. Collect and dispose of 

such waste separately.

• Make use of the return and collection systems available to you, or your local recycling programme. 

Contact your local authority or place of purchase to find out what schemes are available.

• Electrical and electronic equipment contains hazardous substances which, when disposed of 

incorrectly, may leak into the ground. This can contribute to soil and water pollution which is 

hazardous to human health, and endanger wildlife.

• It is essential that consumers look to re-use or recycle electrical or electronic waste to avoid it 

going to landfill sites or incineration without treatment.

LED

Left

Right

Driving control stick

Forwards

Driving control stick

Forwards

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of 

the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the receiver is 

  connected.

•  Consult the dealer or an experienced radio/TV technician for help.

If you cannot eliminate the interference, the FCC requires that you stop using your equipment. 

Warning: Changes or modifications not expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment. This device complies with Part 15 of the 

FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause 

harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.