Digital Monitoring Products Inc PC0136 User Manual

7

SITE CODE

LENGTH:     8

Enter the number of Site Code bits used.  Press any Select Key to enter a number between  

 

1-16.  Default is 8.  Press the COMMAND key to save the entry.

USER CODE

POSITION:  9

Define the User Code start bit position.  Press any Select Key to enter a number between  

 

0-255.  Default is 9.  Press the COMMAND key to save the entry.

USER CODE

LENGTH:   16

Define the total number of User Code bits used.  Press any Select Key to enter a number  

 

between 1-255.  The default is 16.

REQUIRE SITE

CODE:   NO      YES

Press the top row Select key under YES to use a site code and press the COMMAND key to  

 

view the site code entry display. In addition to User Code verification, door access is only  

 

granted when any one site code programmed at the SITE CODE ENTRY option matches the  

 

site code received in the Wiegand string.

You can program up to eight five-digit site codes.  Site code range is 1-65535.  

 

SITE CODE 1 displays first. Any previously programmed site code displays.  Default is 127.   

 

To change the site code, press a select key, then enter the new code. Press the COMMAND  

 

key to save and to display the next site code.

 

Site Codes 2-8 default to blank. 

NO. OF USER CODE

DIGITS:    5

The 734W module recognizes user codes from one to ten digits in length.  Press any top row  

 

Select key to enter a user code digit length between 1-10 digits.  This number must match the  

 

user code number length being programmed in the panel. Default is 5.  

 

All bits are read and converted into a decimal number string. The number string is left  

 

padded with '0' if needed for long user code lengths. When selecting '4' the right digit is  

 

dropped and the next four sent. 

 

Example:  # decoded 

 

 

1234567

 

 

 10 

digits   0001234567

 

5 

digits 

   34567

 

4 

digits 

   3456 

 

This option defines the relay action when communication with the panel has not occurred  

 

for five seconds.  Default is OFF. Press any top row Select key to change the default relay  

 action. 
 

Choose the action required when the 734W cannot establish communication with the panel:

 

Press the first Select key to choose 

OFF (Relay Always Off) — The relay does not turn on  

 

when any Wiegand string is received.  

OFF does not affect any REX operation.  If  

 

 

communication is lost during a door strike, relay remains on for the door strike duration,  

 

but turns off at the end of the door strike timer.

 

Press the second Select key to choose 

SITE (Accept Site Code) — Door access is granted  

 

when the Wiegand site code string received matches any site code programmed at SITE  

 

CODE 1-8.  For details refer back to the REQUIRE SITE CODE option.

 

Press the third Select key to choose 

ANY (Any Wiegand Read) — Door access is granted when  

 

any Wiegand string is received.  

 

Press the fourth Select key to choose 

ON (Relay Always On) — The relay is always on.  

 

Press the COMMAND key to display the next action.  

 

Press the first Select key to choose 

LAST (Keep Last State) — The relay remains in the same  

 

state and does not change when communication is lost. If communication is lost during a  

 

door strike, the relay remains on for the door strike duration, but then returns to it's last  

 

state prior to doing the door strike.

734W

STOP

Press any select key to start the stop routine. When programming in complete, the Version  

 

displays and the keypad can now be removed.

This device complies with CFR47 Part 15 of the FCC rules. 

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

 NO COMM WITH PNL

 OFF  SITE  ANY  ON

 SITE CODE 1:

 (1 - 65,535)    127
 SITE CODE 2:

 (1 - 65,535)    -
 SITE CODE 8:

 (1 - 65,535)    -

 NO COMM WITH PNL

 LAST