Digital Monitoring Products Inc PC0181 User Manual
Digital Monitoring Products
XTLplus Installation and Programming Guide
6
INSTALLATION
Wireless Zones
12.1 Description
XTLplus panels provide 48 wireless zones numbered 1 to 48. A default zone name, zone type, and area
assignment are described and can be changed in Zone Information programming as needed. The defaults are
provided as a programming convenience to help reduce installation time.
Wireless Key Fobs and Outputs
13.1 Description
XTLplus panels provide 8 wireless key fob or output addresses numbered 51 to 54 and 61 to 64. A default
name is provided as a programming convenience to help reduce installation time. The default names are
described in the programming sections of this guide and can be changed in Output Information or Zone
Information programming as needed
Flash LOAD Button
14.1 Description
The XTLplus panel software can be updated via the panel’s PROG programming header. To update the panel
with a new software version, complete the following steps at the protected premises:
Model 399 Cable
Connect a DMP 399 Cable from the PROG header to the serial port of your PC operating Remote Link and
Model 399 Cable
Connect a DMP 399 Cable from the PROG header to the serial port of your PC operating Remote Link and
containing the XTLplus RU file.
1. Start Remote Link and create or open the control panel account that matches the panel to be updated.
2. Set the Connection Information Type to Direct with a baud rate of 38400 and choose the appropriate
1. Start Remote Link and create or open the control panel account that matches the panel to be updated.
2. Set the Connection Information Type to Direct with a baud rate of 38400 and choose the appropriate
COM port.
3. Select Panel>Remote Update, then select the correct RU file for the panel.
4. Press and hold the LOAD button, then press and release the RESET button.
5. Release the LOAD button and click <Update> in Remote Link.
6. After the software update is completed, remove the 399 cable and press the RESET button to resume
4. Press and hold the LOAD button, then press and release the RESET button.
5. Release the LOAD button and click <Update> in Remote Link.
6. After the software update is completed, remove the 399 cable and press the RESET button to resume
normal panel operation.
Model 400 USB Flash Module
1. Press and hold the LOAD button. While holding the LOAD button, press and release the RESET button
2. Release the LOAD button.
3. Connect the USB flash drive to the Model 400 and connect the assembly to the panels PROG header. The
1. Press and hold the LOAD button. While holding the LOAD button, press and release the RESET button
2. Release the LOAD button.
3. Connect the USB flash drive to the Model 400 and connect the assembly to the panels PROG header. The
LED on the Model 400 will flash and display steady green.
4. Press and release the LOAD button on the Model 400 to initiate the firmware update. The LED on model
400 will flash slowly. If the LED displays fast flashes it means the firmware update was unsuccessful.
5. The update will take approximately 4.5 minutes and when complete the LED on the Model 400 will display
steady green.
6. Press and release the RESET button then remove the USB flash drive and Model 400 assembly. For
additional information see Model 400 USB Flash Module Installation Guide (LT-1402).
On-Board Z-Wave Connection
15.1 Description
The XTLplus features an on-board Z-Wave controller that allows short range radio control of Z-Wave devices
that you or your installation company may provide such as; lighting control modules, thermostat controls,
doors, and garage doors. Z-Wave Setup allows you to program the system to control the Z-Wave devices
from Smartphones using the DMP Virtual Keypad App or with the Virtual Keypad Browser. The available setup
options are: Add, List, Remove, Favorites, Transfer and Optimize.
On-Board Wi-Fi Network
16.1 Description
The XTLplus connects directly to a Wi-Fi network for TCP communication using a Wireless-B/G connection.
The XTLplus uses wireless 802.11b/g Wi-Fi technology.
16.2 Wi-Fi LEDs
The Green Wi-Fi LED is located to the right of the wireless LEDs in the upper right of the circuit board.
Wi-Fi LED displays solid when the network is connected and is off when there is no network connectivity. See
Figure 5 for Wi-Fi LED location.