Digital Monitoring Products Inc PC0191 User Manual

8 0 0 - 6 4 1 - 4 2 8 2

I N T R U S I O N   •   F I R E   •   A C C E S S   •   N E T W O R K S

w w w . d m p . c o m

2 5 0 0   N o r t h   P a r t n e r s h i p   B o u l e v a r d

Designed, Engineered and 

Assembled in U.S.A.

S p r i n g fi e l d ,   M i s s o u r i   6 5 8 0 3 - 8 8 7 7

LT

-0694 1.04 © 2016 Digital Monitoring P

roducts, Inc.

16335

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all 

persons. It must not be co-located or operated in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could 

void the user’s authority to operate the equipment.
NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference 

by one or more of the following measures:
-  Reorient or relocate the receiving antenna.
-  Increase the separation between the equipment and receiver.
-  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-  Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Information
This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following 

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, 

including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. 

L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) 

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible 

d’en compromettre le fonctionnement.

Battery 

Life Expectancy  5 years (normal operation) 

Type 

 

3.0V lithium CR123A 

See Battery Life Expectancy for full details.

Frequency Range:   905-924 MHz
Dimensions 

Transmitter Case  3.3” L x 1.6” W x 0.9” H 

Transmitter Base  3.3” L x 1.6” W x 0.1” H 

Magnet Housing  1.5” L x 0.5” W x 0.7” H 

Magnet Spacer 

1.5” L x 0.5” W x 0.1” H

Color 

  White

Housing Material 

Flame retardant ABS

All DMP 1100 Series Wireless Receivers and Panels

U. S. Patent No. 7,239,236

California State Fire Marshal (CSFM)
FCC Part 15 Registration ID CCKPC0191
Industry Canada Registration ID 5251A-PC0191
ANSI/UL 1023 Household Burglar Alarm System Units   

Accessory Magnetically Activated Switch or Door 

 

Contact Transmitter

ANSI/UL 634 Connections and Switches for use with    

Burglar Alarm Systems Accessory