Sam Ash Music Corporation CH88 User Manual

Quick Start - Single System Setup

With the transmitter powered off, install two fresh AA batteries into the CB88 belt
pack or CH88 handheld transmitter. Leave the battery compartment open.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

3. Plug in receiver

4. Turn on receiver

5. Plug receiver into audio system

6. Press Select button to change channel

9. Press and hold SELECT button to IR set

10. Adjust Volume control

7. Install batteries

8. Press button on transmitter to turn on

9. Press and hold Select button to IR set

7. Install batteries

8. Turn on belt pack transmitter

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

3. Plug in receiver

4. Turn on receiver

5. Plug receiver into audio system

6. Press Select button to change channel

9. Press and hold SELECT button to IR set

10. Adjust Volume control

7. Install batteries

8. Press button on transmitter to turn on

9. Press and hold Select button to IR set

7. Install batteries

8. Turn on belt pack transmitter

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

3. Plug in receiver

4. Turn on receiver

5. Plug receiver into audio system

6. Press Select button to change channel

9. Press and hold SELECT button to IR set

10. Adjust Volume control

7. Install batteries

8. Press button on transmitter to turn on

9. Press and hold Select button to IR set

7. Install batteries

8. Turn on belt pack transmitter

Turn on the power to the transmitter by pressing and holding Power switch; the indi-
cator LED will light green.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any

interference received, including

interference that may cause

undesired operation.

FREQ:

542-566MHz

3. Plug in receiver

4. Turn on receiver

5. Plug receiver into audio system

6. Press Select button to change channel

9. Press and hold SELECT button to IR set

10. Adjust Volume control

7. Install batteries

8. Press button on transmitter to turn on

9. Press and hold Select button to IR set

7. Install batteries

8. Turn on belt pack transmitter