ademco 8DL5816OD-1 User Manual
5816OD Wireless Outdoor Sensor – Quick Installation Guide
For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/
WARRANTY For the latest warranty information go to: http://www.security.honeywell.com/hsc/resources/wa/
WARRANTY For the latest warranty information go to: http://www.security.honeywell.com/hsc/resources/wa/
General Information and Component Identification
The Honeywell 5816OD Wireless Outdoor Sensor (referred to as
the Sensor) brings the convenience of wireless technology to the
outdoors. The major features are:
the Sensor) brings the convenience of wireless technology to the
outdoors. The major features are:
Weatherized security protection for an outdoor environment.
Great for sheds, barns, garages, pool gates, fences, and rural
mailbox (notifications).
Great for sheds, barns, garages, pool gates, fences, and rural
mailbox (notifications).
Versatile mounting options on flat and round materials.
Cover and rear tamper detection.
Can be painted to coordinate with mounting surface.
Operating temp: – 40 to +50° C (– 40 to +122° F) at
RH of 100% (rain, snow).
RH of 100% (rain, snow).
Maximum Magnet Gap:
Wood: 1.75 inches
Metal: 1.25 inches
Metal: 1.25 inches
COMPONENT IDENTIFICATION
5816OD-001-V0
SENSOR
MOUNTING
PLATE
MOUNTING
PLATE
MAGNET
MAGNET
SPACER
SPACER
SENSOR
SEALING
COVER
COVER
Installing / Replacing the Batteries
IMPORTANT:
Always change both batteries. Do not mix weak batteries with
new batteries.
new batteries.
Use two (2) lithium 1.5VDC AA cells. (For best life, use
Eveready's
Eveready's
Energizer Ultimate LITHIUM
AA batteries,
Honeywell part number 462)
OBSERVE BATTERY POLARITY.
Battery Replacement:
1. Remove cover screw and swing Sensor to remove from Sensor
1. Remove cover screw and swing Sensor to remove from Sensor
Mounting Plate.
2. Use screwdriver in any pivot point and pry Sealing Cover off.
Replace batteries.
3. Orient the Sealing Cover so the screw hole lines up with the
screw hole in the sensor cover, and press to close.
4. Engage Sensor tabs into mating holes in Sensor Mounting
Plate and swing closed. Secure with cover screw.
5816OD-002-V0
PRY
POINTS
POINTS
TERMINAL BLOCK
FOR EXTERNAL
CONTACT SWITCH
FOR EXTERNAL
CONTACT SWITCH
Mounting Guidelines
This device is intended for vertical surfaces (to be mounted at a
sufficient height) where snow, ice and water buildup will not
interfere with its operation.
sufficient height) where snow, ice and water buildup will not
interfere with its operation.
Mount the Magnet on the magnet sensing side of the Sensor as
identified by the side ribs on the Sensor.
identified by the side ribs on the Sensor.
Mount the Sensor on a stationary surface, and mount the
Magnet on the moveable surface.
Magnet on the moveable surface.
When used on wooden sheds and barns, mount the sensor and
magnet on the inside of the structure.
magnet on the inside of the structure.
Use the Magnet Spacer when mounting on metal surfaces; or
if needed to achieve proper alignment with the Sensor.
if needed to achieve proper alignment with the Sensor.
Use screws suitable for the material being fastened to.
FLAT SURFACES
COVER
SCREW
SCREW
MOUNTING
SCREW (4)
SCREW (4)
5816OD-003-V0
MAGNET
MAGNET
SPACER
SPACER
MOUNTING
SCREW (2)
SCREW (2)
SENSOR
SENSOR
MOUNTING
PLATE
MOUNTING
PLATE
FENCE
GATE
SEE THE BOTTOM OF PAGE 2 FOR FCC & IC
STATEMENTS
STATEMENTS