ademco 8DLLKP500 User Manual
USING THE KEYPAD
The Lyric Smart Keypad is used to control the security functions of the Lyric Smart Controller. The keypad also features two menus for setting various options (see
Keypad Settings Menu section below). Refer to the Lyric Smart Controller’s User Guide for more information about Security functions.
Keypad System Functions
NOTE: Before entering any command, the keys must be lit (key lighting automatically turns off after a period of inactivity, if the Auto Off option is enabled).
If the keys are unlit, press any key before continuing.
Keypad Settings Menu
There are two Settings menus, one for users and one for the installer. Use the
Select, Scroll and Cancel keys to navigate the menus.
Key
Function
Select (1)
Press and hold to start the Settings menu.
Also used to select menu options.
Scroll (0)
Press to scroll through the available menus and the settings
in menus.
Cancel (Away) Cancels the current entry and returns to Status display.
To Access User Settings
1. Press and hold the
Select (1) key until the menu begins.
2. Use the
Scroll (0) key to scroll the settings.
3. Use the
Select key to choose the desired menu item.
4. Use the
Scroll key to toggle the menu options.
5. Press the
Select key to choose an option.
6. Press the
Select key again to save your settings.
User Settings Menu (brackets [ ] indicate default values)
Setting
Options
Notes
Chime
[On]/Off
On: keypad beeps when a zone is faulted if Chime
mode is turned on at the control
Off: keypad does not beep upon faulted zones
Exit Tone
(beeps)
[On]/Off
On: keypad beeps during exit delay period
Off: keypad does not beep during exit delay
Off: keypad does not beep during exit delay
Entry Tone
(beeps)
[On]/Off
On: keypad beeps during entry delay period
Off: keypad does not beep during entry delay
Off: keypad does not beep during entry delay
Voice Volume [Med]/High/Off
Adjusts the desired volume for keypad
announcements.
Off: mutes arm/disarm announcements; alarms are
Off: mutes arm/disarm announcements; alarms are
always announced
Key Level
[Med]/High/Low
Adjusts the brightness of key lighting.
Display Level [Med]/High/Low
Adjusts the brightness of the display.
Backlight
(for keys)
(for keys)
Always On/[Auto Off]
Always On: display remains always on
Auto-Off:
Auto-Off:
display turns off after a period of
inactivity.
Firmware Upgrades
Software upgrades may be available for this product. Upgrades can be installed
manually using the Lyric Smart Controller, or can be done via AlarmNet 360.
To upgrade the keypad firmware using the Lyric Smart Controller, go to the
following Controller menu and follow the prompts:
Security > Tools > enter Code > Advanced > Upgrade Sensor Firmware
RF Exposure
Warning – The antenna(s) used for this device must be installed to provide a separation distance of at
least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une
distance de séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
SUPPORT & WARRANTY
For the latest documentation and online support information, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
To Access Installer Settings
1. Press and hold the
Select (1) key until the menu begins.
2. Enter
Installer Code. The panel displays “Advanced Menu Use Scroll Key”.
3. Use the
Scroll (0) key to scroll the menus.
4. Use the
Select key to choose the desired menu item.
5. Use the
Scroll key to toggle the menu options.
6. Press the
Select key to choose an option.
7. Press the
Select key again to make settings or choose options.
Installer Settings Menu
Setting
Options
Notes
Default Keypad Cancel/Delete
Delete = resets the keypad to its
factory default settings and un-
enrolls the keypad from the Lyric
system. However, the keypad will
remain in the Lyric Controller’s list
of connected devices. If Delete is
used, make sure to un-enroll the
keypad at the controller.
Cancel = exits from Default Keypad
screen without making a change.
Firmware
Use
Use
Scroll to
choose firmware
components
App (version level)
Touch (touch screen)
Boot (boot loader)
RF6 (comm. protocol)
Displays the various keypad
component firmware versions.
See Firmware Upgrades section for
See Firmware Upgrades section for
details on upgrading the keypad
firmware.
FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has
been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part
15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
If using an indoor antenna, have a quality outdoor antenna installed.
•
Reorient the receiving antenna until interference is reduced or eliminated.
•
Move the radio or television receiver away from the receiver/control.
•
Move the antenna leads away from any wire runs to the receiver/control.
•
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute
interférence reçue y compris les interférences causant une reception indésirable.
Ê800-19484pŠ
800-19484 4/15 Rev. A BETA
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright 2015 Honeywell International Inc.
www.honeywell.com/security
FUNCTION
PRESS
NOTES
The Security shield is a single key; the
and
icons are
not
separate buttons. Security status is indicated by color:
Shield State
Meaning
Green unlit
not ready to arm (press and hold Status key
to show faults)
steady
ready to arm
Red
steady
system armed
blinking
system arming, exit delay in progress
unlit
zone fault or zone trouble
Arm Away
Away then enter user code.
Exit delay begins. System arms in Away mode.
(see User Guide for Auto-Stay option, if enabled)
Arm Stay
Stay then enter user code.
Exit delay begins. System arms in Stay mode.
Quick Arm
(if programmed)
Hold
Security Shield for 3
seconds, then select
Away or
Stay arming mode.
Quick Arm allows arming the system without
entering a user code.
Exit delay begins. System arms in selected mode.
Exit delay begins. System arms in selected mode.
Bypass Zones
(if zones are
faulted)
With system not ready:
Away or Stay then enter user
Away or Stay then enter user
code.
Press
Press
Select when prompted.
System automatically bypasses all faulted zones
and arms in the selected mode.
NOTE: Force Bypass must be enabled at the
NOTE: Force Bypass must be enabled at the
controller for this feature to operate.
Panic
(if programmed)
Hold
Panic key for 3 seconds,
then select:
•
Fire
•
Police (default = silent)
•
Medical
The 3 Panic keys light red until one is selected,
then:
•
An alarm signal is sent to the central station
•
Alarm sounding starts (if programmed to do so)
•
If the selected Panic function is programmed to
be silent, the keypad returns to normal state.
Disarm
Security Shield, then enter user
code.
System disarms.
Cancel Silent
Panic Alarm
Security Shield, then enter user
code.
Panic alarm is canceled.
Display
security status
Status
Displays the system’s current security status.
(Armed/Disarmed, Away/Stay/Custom
(Armed/Disarmed, Away/Stay/Custom
arming
mode, exit countdown, Ready/Not Ready, Fault,
Trouble and Bypass conditions.)
Cancel
Cancel
Cancels the entry and returns to Status display.