UTC Fire & Security Americas Corporation Inc 772-DWS User Manual
3
Door/Window & Long Life Door/Window Sensors
Programming
*Ài>ÀÞÊ£äÉÓÎÉ
q If you are connecting a remote device to a door/win-
dow sensor, do not use the built-in reed switches.
q Do not connect fast pulse devices (such as Window
Bugs) to door/window sensors.
q Do not use more than 25 feet of 22-gauge, stranded
wire in any wire run.
q Do not use more than 6 feet of untwisted wire in any
wire run.
q Do not connect more than five switches or more than
one alarm screen to a door/window sensor.
q Do not run wires parallel to electrical wires. If you
can’t avoid a parallel wire run, keep it at least 18 inches
away from electrical wiring.
away from electrical wiring.
q If necessary, you may cross electrical wires at a 90
degree angle.
Programming
The following steps describe the general guidelines for pro-
gramming (learning) the sensor into panel memory. Refer to
the specific panel installation instructions or reference man-
ual for complete programming details.
gramming (learning) the sensor into panel memory. Refer to
the specific panel installation instructions or reference man-
ual for complete programming details.
1.
Set the panel to the program mode.
2.
Proceed to the LEARN SENSORS menu.
3.
Select the appropriate sensor group and sensor number
assignments.
assignments.
4.
Set the external switch (if one is connected) in the
alarm condition (open for normally closed circuits;
closed for normally open circuits).
alarm condition (open for normally closed circuits;
closed for normally open circuits).
5.
Trip the sensor’s tamper switch by removing the sensor
cover.
cover.
6.
Exit program mode.
7.
Place the cover back on the sensor.
Testing
The following steps describe the general guidelines for test-
ing the sensor. Refer to the specific panel installation
instructions or reference manual for complete testing
details.
ing the sensor. Refer to the specific panel installation
instructions or reference manual for complete testing
details.
1.
Set the panel to the dealer sensor test mode.
2.
Trip the sensor.
3.
Listen for interior siren beeps to indicate how many
rounds the panel receives from the sensor. You should
hear 6 to 8 beeps.
rounds the panel receives from the sensor. You should
hear 6 to 8 beeps.
Notes on Testing the LongLife Door/
Window Sensor
Window Sensor
The Long Life Door/Window Sensor has a built-in power-
saver feature that turns on automatically when the sensor is
tripped more than once, within a 4-1/4 minute time period.
saver feature that turns on automatically when the sensor is
tripped more than once, within a 4-1/4 minute time period.
When the power-saver feature is on, the sensor transmits
only half the usual number of data rounds when tripped. For
example, during a dealer sensor test you normally expect to
hear up to 8 data rounds. When the power-saver feature is
on, you may hear only up to 4 data rounds.
only half the usual number of data rounds when tripped. For
example, during a dealer sensor test you normally expect to
hear up to 8 data rounds. When the power-saver feature is
on, you may hear only up to 4 data rounds.
To be sure the sensor has acceptable transmitting range to
the panel, leave the sensor undisturbed in the closed (non-
alarm) condition for 5 minutes before tripping it for testing.
This gives the sensor enough time to turn off the power-
saver feature so you can get accurate sensor test results.
the panel, leave the sensor undisturbed in the closed (non-
alarm) condition for 5 minutes before tripping it for testing.
This gives the sensor enough time to turn off the power-
saver feature so you can get accurate sensor test results.
Specifications
Operating Temperature Range: 0° to 120° F.
Compatibility: All Learn Mode panels
Power Source: 1/2 AA 3.6-volt lithium battery for 60-362,
AA 3.6-volt lithium battery for 60-641
Transmit Range: At least 500 feet, open air
Notices
FCC Part 15 Information to the User
Changes or modifications not expressly approved by Interactive Technolo-
gies, Inc. can void the user’s authority to operate the equipment.
gies, Inc. can void the user’s authority to operate the equipment.
FCC Part 15 Class A
This equipment has been tested and found to comply with the limits for a
class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case users will be required to correct the interference at their own
expense.
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case users will be required to correct the interference at their own
expense.
FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against interference in a resi-
dential installation.
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against interference in a resi-
dential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
q
Reorient or relocate the receiving antenna.
q
Increase the separation between the equipment and receiver.
q
Connect the affected equipment and the panel receiver to separate
outlets, on different branch circuits.
outlets, on different branch circuits.
q
Consult the dealer or an experienced radio/TV technician for help.