Wellsino Electric Company Limited ZH-16002 User Manual

1. Locate the bottom section of the tree which is identified by 

a label on the outer branches marked “A” (Fig 5).

2. Remove the protective plastic cap from the end of the pole, 

(that is pinched to a point), and place that end into the tree 

stand. Be sure that the pointed end of the pole extends to 

the bottom of the stand.

3. Now tighten the eyebolts evenly on the tree stand; being 

careful not to over-tighten (Fig 3).

(We recommend wearing proper clothing in order to prevent 
scratches that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1); 
including the contents of the poly-bag that is adhered to the 
interior flap of the tree’s carton.
Contained in the poly-bag is the remote control which 
operates your tree's 8 function lighting capability.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
An on/off push button foot pedal with cord and plug (Fig 6); 
which is pre-attached at the lowest section of your tree (Fig 5). 
The 5’ tree will have (2) tree sections. The 6.5’ and 7.5’ trees will
have (3) tree sections; (“A”, “B” and “C”; as shown in Fig 5).
The 9’ tree will have (4) tree sections “A”, “B”, “C” and “D”.

1. Remove the tree stand from the plastic bag, loosen the eye 

bolt and open the tree stand to form an “X”.

2. Align the holes for the insertion of the remaining (2) eyebolts.
3. Insert each eyebolt and begin threading in a clockwise 

direction for a couple of rotations only; leaving enough room 
for the tree’s pole from section “A” to be inserted into the 
assembled stand (Fig 2).

4. Place the tree stand in its desired location; as once the tree is 

fully assembled, it may be too difficult to move and relocate.

Included is the remote control that operates the color and 
function of your LED pre-lit and pre-shaped Christmas tree (Fig 7).

Patents pending.

1. If the tree does not illuminate press the on/off button on your 

remote control. If failure to light persists, the battery may need to 
be replaced. Insert three (3) standard AAA batteries (R03 or LR03); 
aligning the appropriate ( +/- ) markings accordingly.

    NOTE: The tree’s 8 function lighting capability is controlled solely 

by the use of the remote control provided. 

    If the tree fails to light due to a damaged or defective remote 

control; please resort to manual on/off push button foot pedal 
operation until a new remote control can be provided through our 
customer service center.

2. If failure to light persists, press the on/off push button foot pedal; 

as it may be in the “Off” mode.

3. If the top of the tree or another individual lettered section does 

not illuminate, remove each section and then reinsert as 
instructed, to ensure the electrical connection is made. 

    NOTE: The tree’s top is designed specifically for a secure and firm 

connection point. Downward force will be needed to ensure that 
the electrical connection occurs.

1. Gently remove the plug from its electrical outlet, and carefully bind 

the cord which contains the on/off push button foot pedal and plug.

2. Beginning with the tree’s top section; lift each section straight up 

from the section below, and continue working downward. 

    NOTE: You may have to slightly wiggle each section as you lift each 

section upward.

3. To remove the bottom and final section; loosen the eyebolts by 

turning in a counter-clockwise direction and lift section “A” from the 

support collar of the tree stand.

4. Gently fold the branches of each section upward, towards the 

center, and position in the storage container.

    NOTE: With the exception of the tree’s “top” section; by holding 

each section upside down; the branches will collapse downward, 

due to the hinging, aiding in the packing of each section into the 

storage container.

5. Fully unthread the eyebolts from the tree’s stand and fold together; 

placing in the storage container.

6. It is recommended to always store the tree in a cool, dry location 

protected from excessive exposure to heat or sunlight. 

    NOTE: Store your remote control in a SAFE & DRY location and 

remove the battery from remote control before storage.

Before operation; three (3) standard AAA batteries (R03 or LR03) 
must be installed into the remote control; by simply removing 
the slide plate located on the back of the remote control.  
The LED pre-lit and pre-shaped Christmas tree’s 8 lighting 
function capability is controlled solely by the use of the remote 
control provided.
NOTE: By reducing the distance from your tree; you may achieve 
better remote control reception.
By pressing the Function or ON/OFF button on the remote 
control; indicator lights will keep you on track as to the exact 
color and function that you are currently on.

    By pressing your function buttons up or down on your remote 

you can choose between the following 8 Functions:

    Steady Warm White
    Steady Multi
    Steady Pastel
    Slow Fade Warm White to Multi
    Color Flip Warm White to Multi
    Warm White Twinkle
    Multi Twinkle
    Pastel Twinkle

4. Carefully cut the nylon strapping bounding the branches 

upright.

    CAUTION: Be extremely careful not to cut any of the exposed 

light set wires.

5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contains an on/off push 

button foot pedal with cord and plug (Fig 6). 

    Remove the twist-tie binding the cord together and insert the 

plug into a working electrical outlet.

7. On/off push button foot pedal operation:
    The on/off push button foot pedal is intended to provide basic 

manual on/off operation only; and therefore cannot provide 
the remote control 8 function lighting capability. 

10. Once section “B” is fully inserted downward into section “A”; 

both section “A” and section “B” will now be lit.

11. Again, carefully cut the nylon strapping bounding the 

branches upright; being extremely careful not to cut any of 
the exposed light set wires.

12. Now gently guide the branches of section “B” downward into 

place.

13. Depending on the height of the tree you have purchased, 

you will continue to build your tree upwards, section by 
section, following the above steps until the tree is completely 
assembled. Each section of the tree is labeled in alphabetical 
order beginning from the bottom to the top.

8. Locate the next section of the tree which is identified by a 

label on the outer branches marked “B” (Fig 5).

9. Remove the protective plastic cap from the end of the pole 

on section “B”; insert that end onto the top of the pole of 
section “A” (Fig 4).

NOTE: Your tree has been designed with EZ-Power™ 
technology; allowing for each of the tree’s remaining sections 
to light up automatically, upon a firm insertion of each 
lettered section (Fig 5).

NOTE: If the tree is powered off by the use of the push 
button foot pedal, remote control or by unplugging it from 
the electrical outlet; when powered back on the tree will 
resume the memory of the last lighting function selected 
with the remote control.

Thank you for your purchase of this pre-lit & pre-shaped 

Christmas tree.
With proper use and care, this tree will provide years of 

trouble-free enjoyment. 
Please follow the instructions below in order to effectively 

assemble and disassemble your tree. 
In the event that you should encounter any issues during the 

assembly of your tree; please refer to the “Troubleshooting” 

portion of this manual or call our toll free customer service 

number at 1-888-831-6656, and a trained representative will 

assist you. 
Customer service hours of operation: 
Monday-Friday: 8:00am – 4:30pm CST. 
Holiday weekends: 
Last weekend in November: 8:00am – 4:30pm CST.
First weekend in December: 8:00am – 4:30pm CST.    
Visit us on the web at www.santasbest.com 

18”

2017 QVC
Slim Frasier Fir Tree Instruction Sheet - 8 Function Remote (English)
Date:  3/7/17

Item # RL50066S-RP79QV (5ft)
             RL65066S-RP79QV (6.5ft)
             RL75066S-RP79QV (7.5ft)
             RL90066S-RP79QV (9ft)

15”