Art Finex Co. Ltd. 3680 User Manual

RFID Reader/Writer Unit

AMG3002

Product Code: ASK3680

AMG3000 Series Electromagnetic Inductive RFID System
13.56MHz Middle Power RFID Reader/Writer Unit

Instruction Sheet

7 Sep. 2017

Precautions for Safe Use

Observe the following precautions when using this product

Suitability for Use

Take all necessary steps to determine the suitability of the product for the systems,
machines, and equipment with which it will be used. Know and observe all
prohibitions of use applicable to this product.

THE QUALITY LEVEL OF THIS PRODUCT IS LIMITED TO A GENERAL
USE. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY, SUCH AS NUCLEAR CONTROL
SYSTEM, RAILROAD SYSTEM, AVIATION SYSTEM, VEHICLES,
COMBUSTION SYSTEM, DIALYSIS EQUIPMENT, LIFE-SUPPORT
EQUIPMENT, OR SAFETY EQUIPMENT.
FOR USE WITH SERIOUS RISK TO HUMAN LIFE OR PROPERTY, OR FOR
USE UNDER CONDITIONS NOT DESCRIBED IN THE SPECIFICATIONS,
ART FINEX CO., LTD. WILL NOT MAKE ANY WARRANTY AGAINST THE
PRODUCTS AND RESULTS OF USING IT.

Class A Product

This is a class A product. In residential areas it may cause radio interference, in
which case the user may be required to take adequate measures to reduce
interference.
Ensure a minimum distance of 23 cm between antenna and human bodies.

Specifications

General Specifications

Item

Specification

Product Name

RFID Reader/Writer Unit

Model Name

AMG3002

Power supply voltage

12VDC to 24VDC（±10%）

Current (Power) consumption

0.4A max ( 3W max )

Ambient operating temperature

-10 to +60ºC（with no icing）

Ambient operating humidity

30% to 80％RH（with no condensation）

Ambient strage temperature

-20 to +70ºC（with no icing）

Ambient strage humidity

30% to 80％RH（with no condensation）

Host Interface

Half-Duplex RS485 (Isolated)

Carrier frequency

13.56MHz

Supporting RFID standards

ISO/IEC 15693

Type of modulation

Amplitude Shift Keying (ASK)

Conducted power

Up to 27dBm (without antenna gain)

Output field strength

(with AT1M12 anntenna)

Up to 63dBuV/m at 3m

Up to 15dBuV/m at 30m

Antenna connections

2 channels (RP-SMA Female connector)

Supporting Antenna

ART Finex AT1M12

Supporting IC Tags

The IC Tags conforming to ISO/IEC 15693

Tag-it HF-I Plus/Pro/Standard

I-CODE SLI/I-CODE SLIX

SRF55V10P/SRF55V02P

MB89R116/MB89R118/MB89R119

Weight

Approx. 110ｇ

Housing Material

Nylon66, PC

Mounting method

35 mm width DIN rail (EN 50022)

Standard Accessories

Phenix Contact #2713722

Ferrite core for power cable

Dimensions

Control Panel

Indicator LED

Indicator

Off

Green

Orange

Red

RUN

Power Off

Running

Initializing

Updating
firmware

COM

Command

waiting

Command
processing

Recieve error

(RS-485)

Send error

(RS-485)

ERR

No error

Command
succeeded

Antenna

disconnected*

Command failured

/System failure*

OPT

Controllable by command

ANT1/ANT2

Antenna

disconnected

Antenna

connected

Command
processing

Command

failured

*1 The LED lights up when the antenna is not connected to either connector of ANT1 /

ANT2.

*2 When the system fails, the LED (Red) is always on.

DIP Switches

The setting contents of DIP switches SW1 and SW2 are reflected at startup.
If you change the settings of the SW1 and or SW2 during operation, the setting
contents will not be reflected until reset or power is turned on again.

Function

Position

Off

Controler ID*

SW1-1

ID can be set from 0 to 31

Ex. ID:18(2+16)

SW1-2

SW1-3

SW1-4

SW1-5

+16

Write Verify

SW1-6

Off

Verify after Write command

Reserved

SW1-7

Fixed

Please use at the Off position

SW1-8

Fixed

Please use at the Off position

Baud Rate

SW2-1 (SW2-1,SW2-2) RS-485 baud rate

(OFF,OFF):9,600bps,

(On,Off):19,200bps

(OFF,On):38,400bps,

(On,On):115,200bps

SW2-2

Data Length

SW2-3

8bit

7bit

RS-485 data length

Parity Bits

SW2-4 (SW2-1,SW2-2) RS-485 parity bits

(OFF,OFF):Non-Parity,

(On,Off):Non-Parity

(OFF,On):Odd Parity,

(On,On):Even Parity

SW2-5

Stop Bits

SW2-6

1bit

2bit

RS-485 stop bits

Protocol

SW2-7

ASI

AMG

Interface protocol type

Terminate*

SW2-8

Off

RS-485 Terminating resistance

*1 The Controller ID is the sum of the values specified by SW1-1 to SW1-5.

When installing multiple devices on the bus, please set different ID each other devices.

*2 Please turn on only device located at the end of bus.

Installation

Wiring

Pin assign of Bus connector

Phoenix Contact

#2713722

Pin Signal

Type

Description

①

RS-485

Connect to SG terminal of RS-485

②

TRX+

RS-485

Connect to (+) terminal of RS-485

③

TRX-

RS-485

Connect to (-) terminal of RS-485

④

VCC

Power

Connect to (+) terminal of Power

⑤

GND

Power

Connect to (-) terminal of Power

Phoenix Contact MINI COMBICON MC 3.81 mm pitch plug 1.5/5-ST-3.81 series
connector is recommended for harness connection to bus connector (#2713722).

Connector installation

Attach the bus connector #2713722 to the fixed DIN rail, and then mount the
AMG3002 after wiring the cables.

Mounting to DIN Rail

When mounting the AMG3002 to DIN Rail,
① Hook the housing to DIN Rail at the point

indicated in the figure.

② Push down the housing in the direction

shown in the figure until it is fixed.

● Allways turned off the power supply when

mounting the AMG3002 to DIN Rail.

Removing from DIN Rail

When removing the AMG3002 from DIN
Rail,
① While pulling the metal fitting at the bottom

of the housing in the direction shown in the
figure,

② Lift the housing in the direction shown in

the figure.

● Allways turned off the power supply when

removing the AMG3002 from DIN Rail.

Regulations and Standards

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

- Properly shielded and grounded cables and connectors must be used for connection

to host computers and/or peripherals in order to meet FCC emission limits.

- AC adaptor with ferrite core must be used for RF interference suppression.

Note:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.

Notice for Korea Radio Law

해당  무선설비는  전파혼신  가능성이  있으므로  인명안전과  관련된  서비스는  할  수
없습니다
A  급  기기  (업무용  방송통신기자재)
이  기기는  업무용  환경에서  사용할목적으로  적합성평가를  받은  기기로서가정용
환경에서  사용하는  경우전파간섭의  우려가  있습니다.
본  기기는  통상  이용  상태의  경우  인체(머리,  몸통)와  20cm  초과하는  거리에서
사용되어야  합니다

Notice for Taiwan Radio Law

低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Contact

■ART Finex Co., Ltd. Tokyo Office

Uchikanda282 5F, 2-15-9, Uchikanda, Chiyoda-Ku, Tokyo, Japan
Tel: +81 (0)3 3526 3870

Fax: +81 (0)3 5289 7352

https://artfinex.co.jp/contact/

Reproduction, distribution, or modification in whole or in part is prohibited without

the prior written consent of ART Finex Co., Ltd.

The information contained in this manual is subject to change without notice. Every

precaution has been taken in the preparation of this manual. Nevertheless,

ART Finex assumes no responsibility for errors or omissions. Neither is any liability

assumed for damages resulting from the use of the information contained in this

publication.

99 ±0.4

+ -

0.5

0.4

22.60

0.35

0.30

(mm)

AMG3002

TRX+

TRX-

em TRX+

TRX-

+
-

VCC

GND

Ferrite Core

Shielded Twisted Pair Cable

(Accessorie)

WARNING

The following contents which may lead to death or

serious injury.

● Do not use the product in environments subject to inflammable, explosive, or

corrosive gases.

●  Do not disassemble, modify, or repair this product in any way.
●  Do not pour water or insert wire in the gaps of the case.
●  Do not touch this product with wet hands.
●  Confirm that the DC power supply voltage is within the rated power supply

voltage (12 VDC-24 VDC) before using it.

● Do not use this product for purposes other than communicating with IC tags.
● This product must be operated with a minimum separation distance of 23 cm

(8.7inch) or more from a person's implanted medical device such as cardiac
pacemakers.

CAUTION

The following contents which may lead to serious

personal injury or damage to property.

● Always turn off the power supply before attaching or removing the product and

antenna cable.

●  Make sure that the wiring is correctly connected and securely fixed.
●  Do not reverse polarity when connecting the power supply.
●  Do not connect anything other than a dedicated antenna to the antenna terminal.
●  Do not cut, damage or modify the antenna cable. Do not pull, bend or twist the

cable with unnecessary force. Do not place heavy objects on the cable or allow
the cable to get pinched in between objects.

●

If you suspect that anything is wrong with the product at any time, stop using it
immediately, turn off the power supply.

●

This product is a communication facility using radio waves of 13.56 MHz which
is the ISM band which can be generally used. For this reason, interference may
occur depending on the application and location to be used. In order to minimize
the influence of this interference, please be confirmed prior to installation. Also,
there is a danger of affecting radio astronomy and medical equipment, etc.
Please pay particular attention to the use in such an environment.

● Do not store / install the product in the following locations :

 Locations subject to flammable, explosive, corrosive gases, dust, metal

powder or salt.

 Locations subject to contact with water, oil, or chemicals.
 Locations where the temperature and humidity conditions specified in the

specification are exceeded or locations where the temperature changes
drastically (where dew condensation occurs).

  Locations subject to outside or direct sunlight.
  Locations subject to shock or vibration.
  Locations subject to near morter, high-voltage or high-current wiring.
  Locations subject to strong electromagnetic field, static electricity occurs.

●

When disposing of the product, dispose of it as industrial waste.

● Wrap the power cable 3 times around the ferrite core of the accessory, install it

within about 9 cm from the AMG3002 side.

● Use cables with a length of 3 m or less for signal and power wiring.
● Use shielded twisted pair cable for signal wiring and connect signal ground (SG)

to shielded wire of twisted pair cable.

● Check the polarity of the power supply / signal line and that the cable connection

is correctly performed.

● Use the DIN rail by grounding (grounding resistance 100 Ω or less).
● Use a power supply whose voltage fluctuation range is within the rated range and

has sufficient margin in output capacity.