Apex Health Care Mfg. Inc. ABBLE User Manual
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to
operate the equipment.
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to
operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause undesired operation of the device.
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
1.
1.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters between the radiator and your body.
and operated with a minimum distance of 20 centimeters between the radiator and your body.
NCC警語:
根據NCC低功率電波輻射性電機管理辦法 規定:
第⼗十⼆二條
經型式認證合格之低功率射頻電機，⾮非經許可，公司、商號或使⽤用者均不得擅⾃自變更頻率、加⼤大功率或變更原設計之特性及功能。
第⼗十四條
低功率射頻電機之使⽤用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應⽴立即停⽤用，並改善⾄至無干擾時⽅方得繼續使⽤用。
前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或⼯工業、科學及醫療⽤用電波輻射性電機設備之干擾。
前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或⼯工業、科學及醫療⽤用電波輻射性電機設備之干擾。
Quick Start Guide
簡易使⽤用⼿手冊
Bluetooth Smart
Bedding Control Box
This Bedding BLE Box adopts
2.4GHz wireless technology of
Bluetooth Low Energy 4.0 to
construct the communications and
controls between user’s mobile
device and the smart bedding
central box.
本產品採⽤用2.4GHz頻段的低功耗藍
⽛牙無線射頻技術，⽤用以建構⽤用⼾戶⾏行動
裝置與電動床主控盒之間的訊號溝通。
Plug in the RJ9 connector to the
slot of smart bedding central box to
get the operating power and build
up the connection.
⾸首先將產品上的 RJ9 接頭妥善插⼊入
電動床主控盒上對應的接⼝口，即可
由主控盒汲取所需的運作電源以及
由主控盒汲取所需的運作電源以及
建⽴立訊號連接。
1
2
Blue LED still start flashing to
indicate the status of waiting to be
paired. Once it’s paired up with
Control Me Apps, Blue LED will be
turned off.
⼀一旦正常啟動運作，產品上的藍燈
會持續閃爍表⽰示正在等待被⽤用⼾戶的
會持續閃爍表⽰示正在等待被⽤用⼾戶的
⼿手機配對。透過 ControlMe Apps
建⽴立連線後藍燈會熄滅。
3
Users can use ControlMe Apps to
wirelessly manage the smart bed,
wirelessly manage the smart bed,
including the bedding position,
massage vibrator, etc..
設定完成後⽤用⼾戶即可開始透過
ControlMe Apps 無線操控電動床的
相關功能，包括床墊姿勢調整、震
動按摩等等。
Apexcare
Model No. : ABBLE